Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...
From Cat 9500 Cores, trying to reach MPLS circuit connected on adjacent Cat 9300. An additional pair of Cat 9500s and 9300 (in separate MDF), are connected to a backup LTE circuit. Routing keeps defaulting to LTE circuit, despite various routing a...
Hi, I am trying to enable the "no service password-recovery" feature on a Cisco ASR 920 running Cisco IOS XE Software, Version 16.06.03. The ROMMON version is Version 15.6(1r)S1. The Configuration register is set to 0x2102. But the feature is not s...
Feb 13 11:52:38.554: %DUAL-5-NBRCHANGE: EIGRP-IPv6 100: Neighbor FE80::2 (Ethernet0/0) is down: holding time expired*Feb 13 11:52:46.255: %DUAL-5-NBRCHANGE: EIGRP-IPv6 100: Neighbor FE80::1 (Ethernet0/0) is up: new adjacency*Feb 13 11:52:50.946: %DUA...
(Please note that all I.P addresses, hostnames, FQDN, etc. mentioned in this post are imaginary) Hello, I wanted to block the domain www.bad-website.com from my network, so I created an ACL like so: myRouter(config)#ip access-list extended NO-BADmyRo...
Hello, how do I apply a policy map to a SVI on 7k. It does not like the command below. int vlan 184ip policy route-map testroute Thank you, Sharonda
Hello experts, I know this is the topic which discusses with a lot of thread, but I took a look and can't found any perfect solution. the classic topology below===ISP A AS 101=== ===ISP B AS 102=== | ...
Hello, I have a topology consisting of 3 routers like the ones shown in the image below. There is MINIMAL configuration on these devices. R1: int g0/0 ip address 71.46.94.1 255.255.255.252 no shutdown ip route 71.46.94.6 255.255.255.255 71.46...
Why would you trunk VLANS in between core nodes? Doesn't OSPF handle routing for IPs behind the vlans from one layer 3 to another?
Hi gurus, I'm kind of at a loss here. I have an older cisco 1811 router which is supposed to have 100mbit port capability. I understand realistically it will get maybe 80mbit or so, and I've been actually getting 70mbit for a long time, as per spee...
Hello, I’m doing a simple Lab to understand the LOOP caused by configuring different Site-Of-Origins (SoO) with BGP in Multihomed sites.The following scheme demonstrates what I did : 3 PEs with MPLS implemented between them. PE-1 is connected to CE...
Hello Guys,One of my customers have SINGLE WEB SERVER, he has successfully NATTED using one public ip using primary ISP public IP and he is able to access it but, now he has done NATTING to that same web server using another public ip (secondary ISP)...
Good morning,We are upgrading our old environment (C2800) to the new Cisco 4000 series routers. We use one router as an bridge from multiple serial interfaces to an Ethernet interface, see attached file. Now we are encountering an problem that the b...
Hi Team, ISR 4331 mention that it has "3 - Total onboard WAN or LAN 10/100/1000 ports" and same it says "2 - RJ-45-based ports". So if I need to have 3x1GE ports can we select ISR 4331 instead of 4351. My requirement is 3x1GE and 2xSFP
hey guys, how MPLS router know it is penultimate hop and do the PHP, I mean the label tagging is base on route table, right ? from the route table, the router should know "what is tthe next hop" only, I think the oruter doesn't know the full topology...
Dear All,I would like to ask you about how to reset default factory on ASA,Router and Switch ( i mean it similar wr erase but if we do command wr erase all the command is gone, so i would like to original command on product.Best Regards,Rechard
