Routing

Hello,Need some help on the below code. we have 2 bgp path ( primary and backup) and i configure 1 subnet to be routed through main path and the rest 3 subnets through backup.on the backup i have the 3 subnet primary and the first subnet as backup ro...

 I'm configuring this topologyI'm puzzled by R6 receiving R2 prefixes because they originate from a remote AS, so they should arrive with a TTL set to 1. I previously utilized EBGP multihop, but I've since removed it, yet the prefixes persist.   I'm ...

Hello Community,Is there any command to turn-off the paging of the commands output on Cisco iOS and display all output without paging? On Dell Switches, there's a command "terminal length 0", but the same doesn't seem available on Cisco iOS.Router#te...

Hello,Very new to the world of ASA. I just purchased a 5516 model to use as my router for my home lab. The goal is to replace my ISP-provided router with the ASA. When I try to connect the ethernet cable from the ONT to my outside interface on the AS...

Hello, I seen a soft reset for bgp and eigrp for to have peer advertise routes. Does ospf have a soft reset or it doesn't and if so why? Thanks,

Rtr1 ----Cost1-----> Rtr2 (Area13)Rtr1 ----Cost1-----> Rtr3 (Area13)Rtr2 ----Cost10----> Rtr3 (Area10)Rtr2 ----Cost10----> Rtr4 (Area0) If i redistribute static route on Rtr2 then Rtr3 learns best route from Rtr1If i redistribute static route on Rtr4...

Any way to reduce CSR1000v load on CPU in EVE-NG? It is very CPU Intensive and increases the temperature very much. I need to lab SR and I know of no other image for regular IOS or IOS-XE that supports that.

Team,On this Te0/0/0.667 subinterface we have more than 200 users. so we set the PPPOE maximum session.After setting up PPPOE maximum session to 1000 , IPTV not connecting automatically and getting option SKIP or RETRY. after select skip IPTV getting...

If i create an event manager applet to capture logs, i can work with a variable called $_syslog_msg. Example:event manager applet RUNATEVERYLOG event syslog pattern "Configured programmatically" maxrun 4 action 1.0 cli command "enable" action 2.0 put...

I have an intermittent internet cut off after around some days of working (5 to 10 days). The router becomes inaccessible by ssh. No ping also from internet and from inside. The architecture includes two switches (CBS350-48FP-4X) with Vlan1.We did no...

Hi,We have mGRE DMVPN tunnle between one Hub and 7 Spokes. Other 6 Spokes are working fine but one Spoke is not connecting to Hub.Spoke shows DMVPN on IKE state (tunnle is not working) and Hub is not adding nhrp entry in table.Spoke DMVPN TunnelPleas...

Hello, I know very little about configuring cisco hardware and need some help..... we are currently running an 1800 router and I obtained a new to me 1921 router and would like to replace the 1800 router with the newer one, I managed to get it factor...

The Cisco document bgp-mvpn-bgp-safi-129-ipv4.pdf (cisco.com) appears to refer to BGP SAFI 129 as the one used for mVPN configurations. This is totally confusing compared to the mVPN profile configuration guide Configure mVPN Profiles within Cisco IO...

Hi Experts, I am testing the MTU size that BDI can support. Please take a look at my config and test below. I configured the physical interface and BDI with MTU 9190. When I do a traceroute mpls, it shows MRU 1500 suggesting that the network interfac...