Hello I had trtied to apply this scenario to my FPR1010 but either due to lack of understand or simply did not fit my needs, I decided the FPR1010 was a Firewall {obviously) and decided to let it be such and work on the ISRC1111. What I have posted b...
Forum Posts
Hello Expert,I’m seeking best-practice guidance for an OSPF hub-and-spoke design and would appreciate feedback on my proposed Area placement.Network summarySites: 5 (1 HQ hub + 4 remote spokes)Requirement: Spokes must only communicate with the Hub; n...
I'm working through getting IOS-XR devices to ZTP.I'm using DHCP Option 67 to pass the URL for a ztp python script.The DHCP offer also includes DNS server options.It seems that if the URL uses FQDN in the URL, the ZTP script will not be downloaded.On...
My inside trunked router port randomly shuts, with no indication of why in the logs. I had debug STP. What's another debug I can enable to try and get an idea why?Router Log Dec 3 2025 01:26:37 UTC: %TRACK-6-STATE: 22 interface Gi0/0/1.2 ip routing U...
Hello, does anyone have this in .pkt i just wanna config it
Hello,Anyone got any thoughts on this? I'm raising a TAC case for it but wondered if anyone else had encountered this problem. Devices: Cisco C1127-8PLTEP (PID: C1127-8PLTEP)Modem: Sierra Wireless WP7607 (FW: SWI9X07Y_02.37.03.05)IOS-XE Versions Tes...
Greetings I got a N540-24Z8Q2C-M and I have an active alarm for a voltage sensor with value 0 0/RP0-CPU-ADM1166_VOUT_CH7.Can this issue could cause more problems in the future? Or this could be an indication of hardware problems and I need to replace...
Hi all, We have an IR1101 with a 5G modem. In logging we can see that it is constantly flapping between 4G and 5G and we want to lock it on 4G.We searched all documentation and tried all posibilities but nothing seems to work. Below some details. Log...
Hello everyone, Let's say I have two networks in different locations. These sites connected together via managed MPLS. I need to forward 10.34.4.0 network's traffic to 192.168.204.0 . I've been reading for hours, but cannot find any solution. Both o...
Resolved! Multicast PIM questions
Hello all,Diving into the PIM "routing protocol" and have a few questions:PIM neighborships - if PIM does not send out any routing updates to its neighbors, what is the point of a PIM neighborship? (In my packet captures, all I ever see are PIM "Hell...
Hi! I have a problem with VRF NAT translations.We have a cisco 1111 router with following configuration:ip vrf WILDNETip vrf WILDNET_PTip vrf WILDNET_TMinterface GigabitEthernet0/0/0description outsideip vrf forwarding WILDNETip address 1.1.1.10 255....
Hi, Router0 is running an active HSRP group for VLAN 10. When the PC requests the MAC address of the default gateway, the router replies with the interface MAC instead of the virtual MAC. As a result, the switches learn the physical MAC, while only t...
I am dealing with strange problem. I am trying to configure openvpn on my RV260. As soon as I click on enable check box apply open on the page grayed out. I have been reading Cisco doc and forum but do not see any solution.I think I am missing some s...
I plan to construct 2 routers which connect with IPsec(Internet-VPN).Therefore, I would like to construct a PPPoE server with [Cisco router] and confirm that [Router A] and [Router B] are configured correctly. Network topology like this.[Router A]-[C...
Hi All,I am trying to influence upstream routers paths into my AS, AS 1, using AS Path Prepend (See crudely drawn picture). However rather than in normal multi-homed scenarios whereby I would just apply a certain prepend on a certain interface connec...
