Server Networking

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Cisco UCS X-Series Energy Efficiency Offer

 

Forum Posts

Hello Guys,I am having an issue for a network scenario which i am working for X.25 POS terminal connectvity.PLs find the attached file .Also is it possible to work work without PAD profile.?Regards,MAX

Hi, I’m having trouble getting DLSw to SNASw working and I’m hoping somebody might have came across this type of problem before. Let me first explain the design we have in place:3174(PU)—s1/1--- 2610–DLSw------telco circuit----------DLSw-7206vxr--...

bkoryus by Level 1
  • 2204 Views
  • 7 replies
  • 0 Helpful votes

While testing ALPS backup peer configs, we noticed that when the primary peer is failed and connectivity is through the backup peer, the ALPS circuit is dropped after 4-5 minutes of inactivity at the terminal. The remote router then goes through the...

ralfini by Level 1
  • 503 Views
  • 2 replies
  • 0 Helpful votes

Hello Forum,is it possible to code snasw upstream link over a subinterface? For example:interface ethernet 0/0no ip addressetc...!subinterface ethernet 0/0.1ip address 10.10.10.1etc...!subinterface ethernet 0/0.2ip address 10.10.11.1etc...!Can I use ...

Hi all,I would like to connect a 3174 controller on my roouter as follows:3174---[SDLC on serial]---RTR---[SNAsw using HPR/IP]---OSA on MVS.i have 3 questions:1/ the 3174 use LLC2. So do i use sdllc command instead of sdlc command ?2/ do i implement ...

edaguet by Level 1
  • 936 Views
  • 3 replies
  • 0 Helpful votes

Hello, I'm needing some assistance with an issue not many seem to know... experts only attempt this:I need to bridge my VoIP and route my Data via RIP v2, EIGRP, and have this bridging and routing go over two serial T1 links to two seperate facilitie...

SNASWITCHING is able to call-out a remote SNA PU if it receives an order from VTAM Host. VTAM host uses DLCADDR parameters to send orders to SNASW. I am not able to find how to code the DLCADDR parameters in the way SNASW understand them.Moreno Sarto...

msartorel by Level 1
  • 1788 Views
  • 17 replies
  • 0 Helpful votes

Hi, I need install a equipment which work with VOIP configuration to support a propietary system but i should use this system to offer in the future other services in the company, what are the Cisco Systems solutíon that a should use ?ThanksFabian

FBARRERAR by Level 1
  • 640 Views
  • 3 replies
  • 0 Helpful votes

Cisco Configurator tells me: Two or more selected items are incompatible. Selected or default-included item [PA-4C-E] is incompatible with: [S72AR1-12123E]. Please change one or more items.Can someone explain this incompatibility? I would like to con...

It is mentionned in the Datasheet that the supervisor 32, support line card using the shared bus and CEF256. But further in the doc we see that this sup does only have the shared bus. Does tha mean that CEF256 card are support only with the shared bu...

cebetant by Level 1
  • 469 Views
  • 2 replies
  • 0 Helpful votes

The 7513 with 12.1.3 IOS , the CIP microcode is 27-9.What cause the following messages?I think it is a bug, but I can't found any bugs by bugs tools:May 17 15:00:22: %DBUS-3-DBUSINTERR: Slot 10, Internal ErrorMay 17 15:00:44: %RSP-3-RESTART: cbus com...