Our branch offices got a problem to work with a CICS.The terminal sent initself request and got +rsp ( there should be bind from CICS) andthen we got NS procure error for CINIT ( CINIT error in reaching the PLU) Is anybody face this problem bef...
This is my scenario : AS400 connect two mainframe as pu2.1 using 2 serial interfaces. One connection is made on sdlc dedicated line, another one via X.25 public network.Question is : I want connect AS400 via Ethernet to a Cisco router with 2 serial i...
Need to know if I can communicate with other vendors' DLSw. Are there any caveats I need to know about? Are there any special configs that need to be entered?
Hi,A connection/disconnection problem is occuring on an interface channel (ECPA-3, hardware 1.2, microcode 28.10)The message logged is : ECPA-3-MSG %PKTS-3-CONSISTENCY: txpkt - NULL handle : unknown 0000000 0Does anyone has already this kind of probl...
We run DLSw, with SRB enabled, over many 7206 routers. I am looking to configure BSTUN on two of these routers to accomodate a bisync point-to-point app, but have been warned by fellow engineers to either a) be "very careful" with this config, of b) ...
Have an existing DLSW+ network, supporting PUT2.0's through IBM 3745's to Mainframe. Mainframe had been upgraded to Z-Series with OSA-Express adapter and APPN. Will be adding a new layer of SNASW routers between the DLSW+ Host end routers and the...
hi,my question:i have a cisco7513 router which is connected to an ibm host over a cip-card.there is the following configuration on the card:..lan TokenRing 7 source-bridge 1127 1 1120 adapter 15 4000.1090.0002 name Geos_Tir and so on.there is a...
In much of the Cisco buffer alloc docs, there are references to IBM features being process switched. What constitutes an IBM feature? DLSw? APPN? SNASw? CSNA? SDLC? QLLC? DLSw encapsulated in frame relay? DLSw that is neither in the originating or de...
Have connected AS/400 from old T1 Channel at 56Kb and moved to serial cable on Cisco 1720 Router. Shows UP/UP and Strnm Sent. IBM says AS400 see poll and ack's but apparently ack never gets to VTAm on Host. Help???This is driving us nuts. IBM noted w...
My user set up 5 stun addresses in a stun interface. And totally there are more than 1000 LUs in the interface. Every LUs session response time is more than 7 seconds. Is it normal?? We want to know how many LUs and PUs I can set up in a stun interf...
Can I use DSPU over two router connected on the same ethernet segment that through two wan links connects with a central site. Both router have a DLSW peer active with the central site and a backup peer configured to another router at the central sit...
I have topo like this:(390)--sdlc---(router a)-------wan------(router b)---ethernet----(as400)appc session can't established,so I capture frame on router b's ethernet,but I found the test frame:smac=0200.0000.2083dmac=4242.4242.0640ssap=0dsap=4I don...
I have connection like this: |------ch 1/0----------------chp b8--------|7507--cip--| |--------s/390 |------ch 1/1----------------chp b9--------|can I...
We have a 7206VXR router on which the router crashinfo is not correctly configured. I would appreciate if someone can kindly let me know the steps and commands involved to correctly write a crashdump to the bootflash or log server.
I was not sure where to post this but, I am desperately in need of some help... We are currently configuring MATIP on 3600 routers....but we seem to be stuck on finding info on a single command....the rest is ok! See below, where/how do we obtain the...
