Hi I'm configurating a UCS C22 M3 but this did not recognize the storage. Now install the Cisco configuration Utility but the issues is the sameThe interface CIMC on the tab Storage displays the next messagestorage controller are not present, You ...
Forum Posts
Having a moment of panic and seeking out options.Bought a pair of UCS 6536 Fabric Interconnects. Mentioned up front we'd be connecting (2) FC SANs. FIs arrive. Go to order cabling & transceivers and receive a quote for $6,500+ per FC transceiver (DS-...
Resolved! USC-X: network configuration
Hi! We have:- servers UCSX-210C-M6- chassis UCSX-9508- fabric UCS-FI-6454We plan to deploy a cluster based on vSphere. What are the best practices network configuration for this type of equipment? Below is an example1 variantExample, for Management c...
I have set dns server and it seems the pc connected to that dns cannot use dns server because of the setting of vlan.can Someone please check how to connect dns server with pc1.b314.IT to CUR_DNS?
Hi, i have configured my server in packet tracer and its DNS settings too. But when i try to access it from Laptop with //www.iot.com which i set in DNS settings of server, it shows Host name unresolved error, however when i put the IP address in URL...
I have a UCSC-PCIE-ID10GC card with outdated firmware. I tried using the Intel version of the updater, but I'm guessing it doesn't work with the Cisco branded card I have, or at the very least it seems to require Cisco firmware in order to work. The ...
Hi.I'm experimentingI installed the DS-SFP-16Gb-SW on the MDS9148 SAN Switch and confirmed the "show int fc0/0 transceiver" command.=========================================================test1-2# show int fc1/3 transceiverfc1/3 sfp is presentName i...
Hello I have a Cisco sf350 switch, we create a new vlan and detect on Linux Server on that vlan that we have a lot of BOOTP/DHCP message become from the switch.07:29:12.423400 IP 0.0.0.0.bootpc > 255.255.255.255.bootps: BOOTP/DHCP, Request from 2c:57...
I encountered a problem where Nexus 5548UP is throwing the FAN_DIR_MISMATCH error on bootup and shuts itself down. The FANs are powersupplies are all matching direction. After 3-4 manual poweroffs the switch will come up properly. Below is the error ...
Hi. Does VXLAN EVPN inter-vxlan routing work in data plane on Nexus 9000v? I followed steps documented, but the ping messages don't pass between vxlans. Intra-vxlan traffic has no issue.
Hi, I've installed CVR-QSFP-SFP10G module to one of free interface of module 'N9K-M12PQ' in order to install SFP-10G-SR interface. the other side is just using SFP-10G-SR with C4500X. the problem is the interface is not coming up. both side of inter...
Resolved! vPC LACP on N9K and Linux Bonding
Hello,I want to setup LACP bonding with proper/optimal configuration between UCS 480M5 with VIC 1455 (4x 25Gb links) and N9K. The UCS server runs Oracle DBs on RHEL82x N9K switches have been vPC LACP (active) mode. From server side 2 links, VIC ports...
Resolved! VDC Port Groupings - N77-F324FQ-25
I'm trying to find the port groups for VDC assignments for the N77-F324FQ-25 module. The data sheet doesn't seem to have it, can't seem to find that information anywhere. The best advise I could find was the show hardware internal dev-port-map - I ...
When I connect to a WLAN, I can get a result as following through ipconfig:Ethernet adapter Ethernet:IPv4 address . . . . . . . . . . . . : 172.19.83.237Subnet Mask . . . . . . . . . . . . : 255.255.255.0Wireless LAN adapter WLAN:IPv4 address . . . ....
Hello, I have such a problem: I am doing the work according to the plan, but when I try to connect to the VPN, it does not let me in, although I did everything correctly manually and without errors. Tell me what could be the problem? And I don't know...
