Heads Up :
The post you are writing will appear in a public forum. Please ensure all content is appropriate for public consumption. Review the employee guidelines for the community here.
Hi folks,I try to get interface traffic counter from FC-Interfaces via snmpwalk from my nexus 5596UP, NX-OS 7.0(1)N1(1). Without success.Everything works for Ethernet interfaces: snmpwalk -v2c -c ****** n5-1-060-4 IFmib.....IF-MIB::ifName.436207616 =...
Implemented using a Cisco UCS validated architecture...2 VMs both on the same vSphere blade = fast (few seconds data upload).The same 2 VMs each on different vSphere blades = slow (few minutes data upload).Same problem regardless of which vSphere bla...
Hi Im looking for advice on the upcoming installation on a terminal server in an environment, I require a new model router as the terminal server any recommendations?
Hello, I just pulled a nexus 5020 off the shelf and thru in a 1200w PSU. The fans in the PSU spin, but no LEDs on the PSU or Nexus are coming on. Any ideas? This is believed to have been a working pull.
I am working with a Nexus5000 configuration which includes a "switchport trunk allowed vlan" specification on the fex-fabric port-channelinterface port-channel100 switchport mode fex-fabric switchport access vlan 999 switchport trunk native vlan 9...
I am using a pair of Nexus 9372TX switches (6.1(2)I3(5)) in a VPC pair as top of rack switches. (The 9k's are in a back to back vpc to 7k core switches)Connected are HP DL380Gen9 servers with 4,10 gig (copper) connections split between the 2 switches...
Hello, I'm trying to understand capabilities of the 9636PQ module in a 9500 chassis. I've read the Nexus 9500 switch architecture whitepaper:http://www.cisco.com/c/en/us/products/collateral/switches/nexus-9000-series-switches/white-paper-c11-729987.h...
Guys and Gals, I am going to put this post here as well. I have put this up on the VMware forums too, but not really sure where i need to start looking. I have 4 ESXI hosts that each have 4x 10gb connections on them. These connections go back to a...
Hi,Dual sided vpc , esx server nic 1 and nic 2 connected to the switch a and b respectively where vpc enabled .after cable disconnected from switch b and reconnected , esx shows nic 'none '.is it because of orphan ports ?Please help
Hi all, would be great to get some feedback for the following topic: we inadvertently purchased our new cisco ucs c220 m4 server with the mlom virtual interface card 1227.can this card be used as a "regular" dual port 10GBe Adapter? can it be configu...
Hello, We are planing to build 2-Server-Rooms , Primary and Secondary. Where we plan to have application mirroring servers , and There will be Live work-load sharing , and live data sync between servers.The both Server-Rooms are separated and are con...
We are having a nexus 9504 switch with SUP-A installed in it.IOS version: NX-OS 7.0.3(I1)2 and we are planning to create more VDC's in it. But in one of the release notes i have read that Nexus 9k does not support multiple vdc's. The Cisco Nexus 900...
Can someone please clarify the following statement from the "Guidelines and Limitations for SMB Direct with RoCE" from the "Cisco UCS Manager GUI Configuration Guide, Release 2.2" Specifically "Cisco UCS Manager does not support RoCE with NVGRE, VXLA...
Note I also posted this in the windows forum... After more research I found that the IPs that are not allowing our PDC to perform a NTP sync are Cisco Nexus devices, and apparently the Dispersion needs to be set to 0 (default is 10). I went to the fo...
