We recently announced the release of our self-serve virtual assistant. You can read the full announcement here. Videos and documents are available within a click for our latest products. Once you've told the bot what device you're using, the context ...
Forum Posts
(Updated September 2023 - Added Catalyst 1200 and Catalyst 1300 ) Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Catalyst 1200 & 1300 Hardware Install...
My company's Cisco Small Business switches SG350 doesn't seem to work with SNMPv3 protocol when sending traps to linux host running snmptrapd. Everything works seamlessly with SNMPv2c, howeven my employeer requires encryption to be used for security ...
hi guys have a good mommentsI have two devices. Cbs350 24fp-4g POE Not Working Unfortunately, the PoE part of both devices is down.There are no hardware problems with the components. I even installed several firmwares, but the ports do not turn...
I have one CBS220-48P-4G running the latest firmware 2.0.2.15 (upgraded March, 22nd 2025).I see that all the ports (doesn't matter if a device is connected to the port) show a PoE fault.The issue started at April 6th, and the first couple of weeks th...
Hi,I lost access, via the console, to my CBS350 switch three days after I added MAC-layer station source addresses to the MAC address table. DoS includes attached devices not being able to receive their dynamic IPv4 addresses. As a test, when a devic...
Hi We have a setup where 14 cameras with gigE interface and poe are connected to a cisco SG350X-24P switch.The switch is setup with jumboframes and flowcontrol. The problem is that some of the ports are flapping once in a while. Output from the log i...
Hallo Zusammen,ich habe ein Problem mit der Stabilität der Netzwerkverbindung in Verbindung mit z.B. C1300 & CBS350 & SX350X. Die Fehlererscheinung macht sich bei allen Switchen gleich bemerkbar. Zeitweise ist nach einem Neustart des PCs kein Link vo...
SG300-28P Have upgraded to the latest firmware but keep getting errors on POE.
I purchased a C1300 for my home office lab explicitly so I could manage the multicast traffic effectively, and avoid flooding my LAN.It clams to have IGMP Querier/Snooping and filtering, but when I come to enable this, it says that Bridge Multicast F...
Prezados bom diaacabamos de instalar um SG220-26 26 em nossa rede, consigo acesso web e ssh no mesmo porem o PING não funciona de outras estações para o switch e também do switch para fora, alguém já pegou caso semelhante
Hi everyone, i just bought a Cisco switch SGE2000 24 ports and i'm trying to figure it out. After 30 seconds reset and changing my IP to a static IP (192.168.1.100), i still can't use admin as username and a blank password to get on the switch and f...
BootROM 1.41Booting from SPI flash General initialization - Version: 1.0.0Serdes initialization - Version: 1.0.2mvCtrlPexPolaritySet: TWSI Write skipped, leaving PEX polarity in EP modePEX: pexIdx 0, detected no linkDDR3 Training Sequence - Ver TIP-1...
disabling i2c error when operating the sf300-24pp switch. I want to run it without the poe board that burned out
Hello, I'm triying to reach the latest firmware update for these switch but it has been remove from cisco download site. It's there a way that i could get it. Appreciate your help on these matter.
Hello, I need some help with switch SF350-24.I have configured my switch like you can see in Picture I. If I connect my laptop to the switch, everything works fine, but if I connect an IP phone (not CISCO brand), the port reconfigures itself. (Pictur...
I got two C1300-12XS which i try to connect to each other via 10GB SFPs. The link wont come up between them. However if i plug in the same SFP and fiber cable to other equipment on one of the sides the link comes up without issue (tried to link from ...
