Software-Defined Access (SD-Access)

Resolved! DNA Templates

Hi all,I have a question regarding templates on DNAC. When does one use onboarding templates? Once the LAN automation is run and the device is being provisioned? Or do you need to run day-n templates if LAN automation is used?When you assign a day-n ...

Resolved! Does DNAC Center 2.3.5+ still have the concept of Fabric Domains?

We have a fairly new deployment that has only ever ran v2.3.5.x and we have just begun our SDA fabric journey. Going through documentation, the majority of which is very old, I keep coming across "fabric domains" in addition to fabric sites. I'm fair...

LAN Automation hostname mapping

HiI'm testing LAN Automation. Specifically I want to pre-import a list of devices and their serial numbers so that they are named correctly during discovery. In the session attributes section of LAN Automation there is a Hostname mapping area and it...

Catalyst 9136 Issues in Fabric Wireless Mode

Hello All,I'm reaching out to see if anyone has experienced any issues with Catalyst 9136 APs in Fabric Wireless mode. We have been using SDA with eWLCs for about two years. So far our most stable codebase has been 17.6.2 through 17.6.4, with most of...

Cluster SSO for 2 border nodes running WLC role

Hello community, Do you know if it is possible to have a SSO cluster between 2 border nodes having also WLC role ? I think it is not possible and there's no other choice than having them in N+1 scenario. Also, if N+1 scenario, the only way to keep th...

Resolved! LISP catch-all entry

yeah... i have 2 sites each with 2 BNs & certain number of ENs. lisp configurations are mainly identical (obviously RLOC data is different). Now when i'm looking on the Subject on each Site i can see different output (not sure what inherits what ther...

Adding a new switch to an existing stack

Hello, We have installed two new switches (5&6) on an existing Fabric Stack Edge (4 switches), we can see all the S/N on the DNAC Inventory, but device-tracking configuration is not applied on all new ports/switches. SW-WTCP3-NT-S-1#show switch det...

Resolved! Selecting Software Defined Access products and solution and best CVD

Dears;We are on the verge of acquiring a SDA solution on this final stage we shall decide the amount of device that we should secure, saying this let me present my questions.1. Since C9120AXI-E and C9130AXE-E are similar products what is the advantag...

Resolved! LISP Route in "Route_rejected" status?

Hi,First time post. Apologies in advance if this a too in depth a question for here, but you don't know unless you try.The scenario is that we are on the journey of moving to SD-Access. We have a normal fabric with a standard VN setup, up and working...

Resolved! Cant connect to network, but first time work

Hello,I am having a complicated issue, I am doing some test with the TAC but its a bit more than that I believe. Here is my problem, when you connect the the network the first time it work fine. If you click disconnect and reconnect it says ''Cant co...

SD Access and DNA

HiWe are full SD Access at work now and I was wondering could I manage a device via DNAC that isnt part of the Fabric on a site? So I want to install a 2 Switch stack in our DMZ I'm wondering if this is possible then maybe I could still use DNAC to k...

DNAC ISE Intergration

HiCan ayone explain and add link on how to set up DNAC/ISE Intergration and what technoligies are used,?? (is the intergration Cert based) ??.Thanks

Resolved! Apply a different Authentication Template to some specific switchports

Hello guys, In DNAC, the Authentication Template can be tuned to adjust the Authentication method order, the timers, etc. This template is represented as an IOS-XE template which itself calls a policy-map (ex: "PMAP_DefaultWiredDot1xClosedAuth_1X_MAB...

IP Phone registration delay over SDA

Hi, We are implementing our new SDA network We have an issue for the ip phones registration that it takes a very long time to register to CUCM [about 55 minutes] When it connected, it got ip address from infoblox, then it send request to CUCM untill...

SDA Default borders and firewall fusion

HiWe are proposing an SDA solution to a customer. They intend to retain a pair of 3rd party firewalls as their fusion device. The intention is to connect each Border to one of the firewalls. However, since the firewalls are in HA only one will be ...

Software-Defined Access (SD-Access)

Forum Posts

Resolved! DNA Templates

Resolved! Does DNAC Center 2.3.5+ still have the concept of Fabric Domains?

LAN Automation hostname mapping

Catalyst 9136 Issues in Fabric Wireless Mode

Cluster SSO for 2 border nodes running WLC role

Resolved! LISP catch-all entry

Adding a new switch to an existing stack

Resolved! Selecting Software Defined Access products and solution and best CVD

Resolved! LISP Route in "Route_rejected" status?

Resolved! Cant connect to network, but first time work

SD Access and DNA

DNAC ISE Intergration

Resolved! Apply a different Authentication Template to some specific switchports

IP Phone registration delay over SDA

SDA Default borders and firewall fusion

Network Templates filtering by Site shows irrelevant templates

Use different ISE for guest Wireless & BYOD in DNA-c

DNAC Command Runner - list of support commands:

Collocated L2Border + Edge?

Xconnect / EoMPLS within SDA

Catalyst 8200/8300 - SDA Control Plane Scale

SDA DNA Centre

SDA and ISE Question