Switches - Small Business

Good afternoon commmunity,   We are having troubles with a SG220 device. We have two switches a SG200 and a SG220, when we applied the configuration (that you can see attached to this case) to the SG200 device it work perfectly, but when we try to re...

Hi, Regarding CiscoSG550 stackable switch.The switch has 48 ports, and can be connected to 7 other switches (8 stacks).I would like to fetch only the ports that are in use - If one switch, just the 48 ports.If 2 switches are connected so these 96 por...

Can I connect four cisco AP 1832I to the cisco SG250-10P-K9-EU 8-port POE switch hub?15.4W * 1832I 4pcsIs it possible?

I have an SG300 with fully functional VLAN routing between 4 VLANs that will not forward to the default route. I am able to ping/traceroute to the default route IP configured on the SG300 of the switch from all VLANs, but when trying to access anythi...

I'm looking for the thresholds for operating temperature for this switch and can't find it anywhere. The data sheet gives specs for ambient temp, but that's all. show system and show environment all or show environment temp status don't give the info...

Hello Experts, I have just bought RV110W and installed it with Bell Hub2000 router, and I connect my RV110W WAN to Bell Hub 2000 LAN port 4, I have also put my RV110W in the DMZ with Bell Hub 2000 setting and I have 2 VLANs, VLAN1 is for WIFI (192.16...

I have two Catalyst 2960-X 48 GigE PoE 370W, 2 x 10G SFP+ LAN Base switches, I tried connect both switches with multimode fiber cable distance 150 meters with help of Transceiver SFP-10G-SR= now I am unable to connect both switches.

Dear Team,I have 17 small business switches model no. is SG-300-10 Mpp in my LAN  when I configure the Vlans at switch then i am not able to access the switch through telnet/remotely  because switch port do not remain the vlan-1 part I assigned the I...

Greetings,I have around 10 Small Business Switches from Cisco in my network (like SG550, SG350, ...)I do not have much experience with Cisco switching, VLANS and all those fancy things, and thus I always need external support in case of maintenance/e...

So I am having trouble accessing the web interface for my switch. I am in the command line and it shows as follows when I put in the command show ip interface:Gateway IP Address Activity status Type----------------------- ----------------------- ----...

Hi, Ive been checking Vlan - port relation in a few Cisco switches CiscoSG220/250/300/350/500. There is:dot1qVlanCurrentEgressPorts  "1.3.6.1.2.1.17.7.1.4.2.1.4.0"and another OIDdot1qVlanStaticEgressPorts = "1.3.6.1.2.1.17.7.1.4.3.1.2" In some models...

Just updated one of my SG300-10 from 1.4.10.6 to 1.4.11.2. Since then I cannot access the switch with the webbrowser via HTTPS anymore. Booting the other image with 1.4.10.6 via SSH resolves the issue. For now I will stay with 1.4.10.6 and will not u...

Can anyone advise above, my thought is the active ACL cannot be amend coz I am getting error, Cannot modify active list I am think I need to create a new 1 management profile with all the changes, make it active to replace the current 1. Am I correct...

Is it possible to have Cisco ISE filter out commands for users with TACACS+ Command Sets?  Is my only option to use the 3 privilege levels(1, 7, 15)?