We recently announced the release of our self-serve virtual assistant. You can read the full announcement here. Videos and documents are available within a click for our latest products. Once you've told the bot what device you're using, the context ...
Forum Posts
(Updated September 2023 - Added Catalyst 1200 and Catalyst 1300 ) Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Catalyst 1200 & 1300 Hardware Install...
Hi. I have in front of me an SG300-52P.It is hardware version V3, as shown both on the sticker on the back, and from "Status and Statistics", "System Summery". It is currently running firmware version 1.3.5.58, which is quite old. I wish to upgrade t...
Resolved! SG250-08-K9 mounting kit
Hi,Recently i have an issue, i brough the SG250-08 port, but it not come with any mounting kit, and also no part available for me to order for rack mounk kit, can advise on the SKU for the 8 port rack mount? Thank you.
Hello,we have two new switches, a SG350X-48 and a SG350X-48P. On both i have configured a LAG with the two 10GBit Ports (XG1/XG2)But one port is always on standby. what can be the reason for that?On both is the same firmware i flashed 3 Weeks ago.Man...
On firmware 2.5.0.78, as well as on 2.4.5.71, there is a discrepancy between the creation time of files in the file directory menu. Practically it was possible to find out that, for example, the Operation Type Dublicate Running configuration in Start...
On firmware 2.5.0.78 as well as on 2.4.5.71 in the GUI there is no possibility in the manual settings to specify the default gateway. This feature is only present in the Getting Started Wizard.Or, alternatively, specify the gateway through the CLI. P...
Hello, I am working on an SG300-28P that is doing dhcp for a vlan. The network pool is showing the number of leased addresses is equal to the size of the DHCP scope in the settings. But when I look at the address bindings, there are plenty of lease...
Resolved! SF300 - Inter vlan routing
Hello,I'm new on Cisco environment and I try to install a network with that. I activate the L3 Mode to get router functionnalities for my SF300. So, I create 2 VLAN (40 an 50). I affect some ports to this VLAN (VLAN 40= FE1 and FE2 and VLAN 50 = FE20...
If i enable Access Profile and only allow https, ssh to access the switch from certain IP. If i forget the userid and pwd, the only way is to use password recovery in CLI and console is able to use after power cycle the sw?
I've seen lots of posts from people having problems routing traffic between two vlans with some complicated examples. Can anyone post a simple step-by-step example for an SG300 switch (in layer 3 mode) to configure two vlans and sending traffic betw...
I have a SG200-26P. I have the most simple question imaginable, but it's not answered anywhere that I can find. Here goes:There are 24 "regular" ports on the switch.In addition to the 24 ports there is a second set of 4 ports to the right of the 24...
Hi. Sometimes I Wonder if Firmware are tested before public release. We have a stack of 4 brand new SG500X. I have the same problem on all Firmware I tested so far, including the latest (dated 2 feb): => There's no way to change Management IPV4 Addre...
Hi everyone, I hope you guys can help me with this one, Here is my current networkTo make that work I have created 2 static routes on my firewalls that point to my sw's vlan interfaces Gateway that way I can talk from 10 to 500 No I want to end those...
Hi all, I'm having an issue with getting wake on LAN working and am hoping someone can help me out. Our network is comprised of a number of Cisco SG500-52 switches on which we have configured port security to use MAC address bypass and RADIUS. The ma...
Hi again, I am slowly getting to the correct configuration thanks to a lot of assistance from this forum. I am at the point where the VLANs are created and I can access the internet from each device and I can ping devices on other VLANs. I can als...
Resolved! SG300-10 Console Settings??
Hello all,I am trying to connect to the console of this SG300-10 using a Cisco console cable, but am not getting anywhere with an actual connection. I am using Putty with the settings of 9600-8-n-1-None-None. I have also tried with baud rate of 19200...
