Update: This portion of the project has finished earlier than initial projections. We are approaching our latest step in relabelling posts across the Small Business board. 1 week from today, read-only mode will be active on this discussion board fro...
Forum Posts
Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Catalyst 1200 & 1300 Hardware Installation Guide - Catalyst 1300 Hardware Installation Guide - Catalyst ...
Resolved! SG220-26 VLANS PFSense
Excuse the newbie in me, VLANS are new to me and I've decided to practice and learn a little bit more about them. I have a PFSense router box that I made, I have 3 VLANS assigned to one of the interfaces, each with their own DHCP server. VLAN 10 - 19...
What is the link for selecting cisco online simulator for different products / switches? I have found couple of links for SG-300 and SG-200 series switches. I want to try online simulator for SG-500 and Catalys 2960 series. Are they available, if so ...
Resolved! SG-300 10 PP not booting
Hello,I have one Cisco SG-300 10 PP switch. Earlier this was working fine but suddenly it stopped working. I took this device on the console to see what is happening and I got error messages as follows. I have tried with firmware upgrade but nothing ...
For port mirroring on the SG250X or (SG350X), the documentation states up to 4 (or 8) interfaces per session. However, it does not state how many sessions of 8 interfaces each I can have, or if each session can all mirror to the same destination. Co...
I am trying to setup port mirror on an SG200 Switch. I go to Administration and Diagnostics and then Port and VLAN mirroringI select GE1 as the destination (Capture Port) and VLAN10 as the Source (packets to capture)When I select Apply I get the err...
Trying to connect some POE IP cameras via Cat6 cable, but not able to power these cameras when connected to the SG110D-08 switch. Switch came with a small AC power adapter "Model: DSA-12PF-12FUS 120100" and "Output: +12V at 1A" to power the unit. I...
Hello, folks.I`m successfully configured 3 Cisco SG300-28 to use Dynamic 802.1x VLANs and Guest VLAN at the same time, so if device doesn't respond to auth request, then Guest VLAN applied to the port. All works excellent, checked with Windows and Ma...
Anyone have an idea what would be causing this? Flash Memory Log TableShowing 1-19 of 19 10 20 30 50 per page Log IndexLog TimeSeverityDescription21474659912017-Jun-15 11:50:36Emergency%DHCP-F-HASH: Failed insert to DHCPP_alloc_hash_id hash tabl...
I am new to the 350. I have a VLAN set up for voice using 10.10.0.0 subnet for DHCP. The IP phones are receiving IP addresses but a desktop will not receive a IP address. What am I missing? Thanks.
Hi!Does anyone know the name of the operating system running on the Cisco ESW500 switches?
Hola, para solicitar su ayuda en la creación de los puertos truncados en un SG500-52P, el problema que se presenta en la creación de un puerto troncal que se puede ver todo el vlan creado y lograr una interacción con ellos, espero y encuentre Ayuda c...
Hi Everyone, I often hear that end user desktops should be configured with access ports, not trunk ports. I understand that this is for security reasons. However, on my SG300/350 series switches, there is a preconfigured Smartport value for desktops...
I have a small network with a number of sg300-28p's (8).Two of them have 'failed' after recently upgrading to the 1.3.0.62 firmware release. One failed immediately after upgrading (the below symptoms started on the first boot after upgrade) -- anoth...
I have two stacked SG500-52P units. These units were power cycled last night due to our UPS becoming exhausted after an extended power failure. Since coming back up a certain bank of port (7-12, 31-36) have been having POE issue. They will show large...
Resolved! Vunerability scan SG300
I have recently upgraded the firmware on a SG300-28 to 1.4.10.6I am now getting a vulnerability scan result with the title: Web Server Generates CORS Headers Using User Supplied ValuesThis is being flagged on port 80 and port 443.Does anyone have an ...
