Switches - Small Business

Hello, I'm looking for IOS version ce500-lanbase-mz.122-25.FY of the Catalyst Express 500 but this model is not listed on the download categories for switches on Cisco.com. Once, maybe one year ago, i downloaded from there this IOS version but unfor...

We have several SFP-300 series PoE switches already configured and in production usage.What is the appropriate procedure to export the configuration from one of these switches, then import into a newly-purchased switch of the same model??The only thi...

Have a question regarding the configuration of an SMB SG500-28P switch which we set up to be stacked with 4 other switches (all are SMB SG50028P). We preconfigured the switch before going and installing at the customer's site. When onsite we found it...

Hello, I would like to reboot a SG300 switch via snmp but I'm not able to. Here is my setup: 1 SG300 switch: 10.1.0.105 - Firmware Version (Active Image): 1.4.0.88 1 snmp management device: 10.1.0.9 - linux snmp is enabled on the switch  created a c...

Hey, I've got a question regarding this particular switch. I am trying to get part of my network configured and the only thing I have left is this switch. On it I have multiple VLANs but for the sake of simplicity and my problem, I have our user sub...

Goodday everyone, I have Small Business SG200-50 Cisco Switch for our business, the download speed of the internet is 100mb and the upload speed is 15mb, I would like to limit the bandwidth 10mb download and 1mb upload per device, but i am new to C...

Hi, I am getting an error in Cisco 2960 and HP ProCurve 2920 Switches I am having an issue with Printers only to directly go to VLAN1 as I can't setup for authentication, below is the port configuration. Everything is working fine as of my need exce...

For some reason this is just eluding me.  Using WAP371s attached to SG300 PoE swtiches we find that they become unstable after a few days in some situations (in others they never get flaky, it's very strange) and would like to use the Time Range opti...

Hello all, I have an Sg500X that I am configuring. I am having a problem configuring te1/1/1. I can pull it up through a console session. I get the conf-if I add switchport mode trunk. Then exit and sh run-config and there is no interface listed for...

Hi everyone. I've question about multiple policy restrictions. Allready checked google and cisco communities - didn't found anything special.The case is:I've a test environment based on SG500x. There are 2 accounts (admin) and (backup) with password ...

Hi, we plan to use the sg300 at the workplace. The only function they do not support are some special radius attributes. radius-server attribute 6 on-for-login-authradius-server attribute 8 include-in-access-reqradius-server attribute 25 access-req...

Hi, I recently purchased a used sg300-28p switch here in Australia, the ad for the switch indicated that it would come with a rackmount kit however it was a typo on behalf of the seller. As such, I am searching for a replacement rackmount kit and w...

Hi, I need help to configure the SG300-10P switch for the following:port 9 connect to router (10.0.1.1) to internetVlan 1 (default) 10.0.1.200: ports 1 - 4 & 10: use for PCs and IP phonesVlan 2: 10.0.2.1: port 5, port 6, use for printersVlan 3: 10.0....

Hi all,I have a Cisco SG300-20 L3 switch and want to realize two separate VLans with one common Internet access (something like a guest access to the internet).The internet modem is a Cisco EPC3208G.My problem is that despite that I can ping everyone...

When I try to download version 1.4.8.06 for an SG300-10P I get a poage not found message. Could someone at Cisco inform the appropriate team that this link is broken please?