Switches - Small Business

I need help determining if it is possible to use an SPA500 series IP phone with attached PC with the SLM2008 switch.  I configured all ports for all VLAN's, but the phones are not getting the voice VLAN (100) IP address, they get the data VLAN (1) IP...

Hi Experts,one of my customers tries to install aSLM2024G5 Switch.The Switch is new out of the box.After connecting a PC to one of the Switchports, no matter where the ports shuts down after ~30 sec.Does somebody has a idea how to isolate the problem...

Hi everyone,I am trying to configure a 1811 router to do inter-vlan routing for my SLM2024 switch. Going thru previous posts, it advised setting one port, which is not associated with any vlans, with link aggregation. Afterwards, join that port to th...

Does anybody know if there is a features comparison someplace between these two switches?  Or if anybody knows of some of the main differences please share by all means. At first glance on the pages for both units, they're both 24port PoE switches th...

Hi to whom may concern, Can the following switches (ESW-520-24P-K9) x3 & ESW-520-48P-K9 able to support inline power for  74 x WRT610N  ?Thanks

I am currently testing 80 units (SF100D-05) and so far (after 20 units tested) 10 are not working properly.It's always 1,2 or 3 different ports that do not seem to connect properly (not status led on). On a single unit its always the same ports, but ...

Hello Everyone.  Thank you all for the help with my last post.  I have another wonderful problem that I've been trying to figure out myself for the last few days that I could really use some help with.  It turns out, that I have no idea how to set up...

HiApparently Cisco Small Business has come up with their own SFP(Mini-gbic) transceiver.http://www.cisco.com/en/US/products/ps9934/prod_models_comparison.htmlId like to know if the Cisco's version of GLC-SX-MM( SFP LC connector, SX transceiver) can b...

Hi All,I have the following equipments in my small network1x UC5604x IP Phones1x Catalyst 3560x as CoreSwitch2x ESW 540 as AccessSwitchI am trying to deploy a call recording feature on the VOIP UC system.The call recording solution i am using is the ...

I have a sd208 switch (bought about a year ago) with a big power adapter. And you can tell the energy this power adapter wastes, by the heat it produces. About a month ago I bought a sd205 switch which came with a near 75% efficiency power adapter. B...

Hi,I have two SRW2016's on opposites sides of a property. There is a Fiber Cable running from one unit to the other. Each unit has a shared MiniGBIC (Port 16) which I have installed a MGBLH1 - SFP (mini-GBIC) transceiver module. There is a SFP Fiber ...

I have an SFE2000 operating in Layer 3 mode. I've set up 2 IP addresses on it which are the following:IP: 172.20.72.22 mask: 255.255.248.0IP: 172.20.80.252mask: 255.255.255.0Under the IP Routing section I've set up routing to the internet by putting ...

I installed new SRW208P switch and I mada an uplink connection with SRW 2024 switch (using GE port).when I am trying to connect AVAYA IP Phone to the SRW208P port, the set trying to get an IP address from the DHCP server and failed to get it.some tim...

Hi everyone.I have just bought a Sfe1000P, but i have a problem with it. I I have created multiple vlan, we also uses ine the company, and it works fine. From new it had vlan 10 and vlan 100 as default. The problem is that our voice vlan number is 10...