Hi,we are using Cisco Nexus 5672 switches as our core switches and would like to use NetFlow to export flows. However, all ports on the switches are layer 2 switchports and NX-OS 7.0 does not even show the needed commands for attaching a flow monitor...
Forum Posts
hello Team, I am trying to configure 802.1x on the 2560 switches. We have some ATAs connected. I configured the MAB on the switch and configured the windows IAS server with the ATA MAC as user/password. However; when i connect the ATA to the switch p...
Resolved! IOS XR Softaware crypto image
Hi, What is the difference on XR-NC55-P-06.03XR-NC55-PK9-06.03 I understand that the K9 image is a crypto image. But how does it differ and what benefits does it give to the end user? BR Andreas
Resolved! QinQ Termination on ASR920
Hi Guys I don't have allot of experience with ASR's first time deploying one of these. we have mainly been using ME3400 Switches as our Customer CE's. Our client is deploying a small office and we need to tunnell all client vlans across the provider ...
I have 2960's switches that are experiencing a huge number of total output drops on all connected interfaces. Yesterday i cleared all counters and today i have 155817809 number on my uplink trunk port connected to ASA.I dont have any qos enabled on ...
Resolved! ITU-T G.8032 Protocol Supporter Models
Hi Everyone,We need to Cisco switches which providing ITU-T G.8032 protocol. This switch(es) also should be on Layer 3. I've checked all datasheets but i couldn't reach this information. Can somebody help me about it, please?Thank you so much.
Hi All, I have been able to configure spanning tree and a port channel to help with redundancy. The issue I am facing now is that when I switch the left side multilayer switch off the right side will not allow pings from the clients to the routers. A...
Dears,I m proposing 350X switch for the small business organization, but i m confused with the poe allocation, according to the table below, as it is mentioned in the table below, 382 W power supply can provide power to 32 no's of POE /POE+ ports and...
Hello, I'm working on old switches Cisco CE500, I know we can configure it with 2 manners, GUI and GUI CLI.For GUI CLI I've seen the "write" command, and I beleive we can "wr" the config we make with GUI CLI like that, like if we were working on a "r...
Resolved! VLAN trunking issue
Hi There, We have few VLANs span across 2 cisco 3750 switches. Switch1 and Switch2. Configuration for both the switches is attached. VLANs across switches is accessible with the following issues. 1. The switch 2 can not ping VLAN Interface IP of s...
Hi, I am looking to create a CLI application which will run the following command: show port-security address | i <mac> This will return the interface the mac address is on - I want to store this in a variable.. and then use the below command to clea...
Hey, i have a problem with my Cisco device (Catalyst 3560G 48Port PoE).I cant ping the switch or ping a Client(Pc). I added the Config and removed all private informations. test-sw-1#sh ruBuilding configuration... Current configuration : 4192 bytes!v...
I have an 1841 router and it gets stuck, i'm hoping someone can help me fix this as i think its a corrupt cookie:System Bootstrap, Version 12.3(8r)T9, RELEASE SOFTWARE (fc1)Technical Support: http://www.cisco.com/techsupportCopyright (c) 2004 by cisc...
Resolved! L2 interface to L3 interface
Hi Experts,Is it possible to convert a L2 interface to L3 interface????Today i tried to configure IP address in 1811router. Interface fa6. But it showed some error as "L2 interface is ot able to configure an IP address." I have enable "ip routing" in...
Hi,We've used IE2000 switches in one of our project network. Customer requirement calls for blocking of any unused ports. Does this switch have any web interface or we need Configuration Engine or Professional software to block the ports?
