Hello, Cisco Community!I’m really happy to share that I’ll be hosting the Cisco Community Lab Series, a brand-new hands-on learning journey designed to help you build practical networking skills step by step.Every Thursday at 8 PM EST, I’ll post a ne...
Forum Posts
I've got 3 x WS-C2960CX-8PC-L units and for some reason I can not get accounting interim updates to work. Normal start-stop accounting is working fine. If I compare the output of show authentication sessions int <intname> details command, on the 2960...
Resolved! Extend Layer 2 VLAN over Metro Ethernet
Hello, We are moving data centers. We have metro ether circuit between two data center and we are using ASR routers (CE) at both locations. The ports on the ASRs connected to metro ethernet are layer 3 using 172.16.1.0/24 address range to connect t...
I'm investigating the various configuration options for IWAN and have run into one setting that does not appear to be clearly defined. Based on this configuration guide https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/pfrv3/configuration/xe-16-6/...
Good,I have a problem with applying the configuration in nexus 5k. Commit Failed
Resolved! Stack Configuration on WS-C3650-24TD-S
Hi, kindly help me to prepare stack on WS-C3650-24TD-S switches. we are planning to configure 2 node stack (two switches on each stack). 1. what is the configuration for stack formation on Cisco 3650-24TD-S switches. 2. how can we verify the stac...
Folks, How can i modify this script to allow me to login to the switch when the tacacs server is not enabled. Bacially local login as a backup for AAA login. aaa authentication login default group default enableaaa authentication login n...
Hi all,I have question on Portfast .i have layer 3 switch that connects to another layer 3 switch.here is switch 1 port configinterface GigabitEthernet1/2 description uplink bmanysw02 switchport trunk encapsulation isl switchport trunk allowed vlan 1...
Ok. I have a Etc Ion light board that is connected to the SF302-08pp switch that will also have multiple gateways to run dmx so that I can control multiple lighting instruments. I have everything hooked up and connect to switch via rj45 to do the ...
Resolved! AutoConf
I am trying to enable autoconf on WS-C2960X-48TS-L, but am unable to. Could someone please guide me. Switch Ports Model SW Version SW Image ------ ----- ----- ---------- ---------- * 1 52 WS-C2960X-48TS-L 15.0(2a)EX5 C2960X-UNIVERSALK9-M tes...
Resolved! vPC Keep Alive IP addresses
I am about to refresh an environment with about 40 vPC pairs of Nexus 9K. I am considering using the IPv4 Link Local addressing for the keep alive links: RFC 3927 - 169.254.0.0/16. This is because this range is otherwise unusable and unrouteable. Has...
Resolved! Vlan layer 3 on Catalsyt 3650
Hi Everyone, Since two week, i work on new network infrastrucre. With RGPD plan we need to isolate somes employee so i use vlan for that. Overall the configuration work fine, but now i need to same similar setting with guest wifi. It's little bit c...
Is there a way to limit what advertisements are being sent to an EIGRP neighbor? The scenario is as follows. We are using EIGRP for dynamic routing between branches and home office. At the home office there is a connection going to a 3rd party co...
Hi All , I am currently working on a project where I need to migrate the routing protocol from EIGRP to OSPF in one of our company data center. There are around 100 network devices in the site which include both Cisco and Brocade , all the access la...
Hello community, I am struggling with problem with some CSR1000v for about 2 weeks now and since I think that I nearly tried and read everything I could on the internet, I will try to find some help here now. The situation is the following: To prep...
Hi i've hit a little bit of a problem, to do with an SCCM deployment, basically, option 60 ascii "PXEClient" is configured and boots all devices that use UEFI, however, some legacy devices are still requiring SCCM deployment, devices with BIOS's do...
