Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

Hello, Cisco Community!I’m really happy to share that I’ll be hosting the Cisco Community Lab Series, a brand-new hands-on learning journey designed to help you build practical networking skills step by step.Every Thursday at 8 PM EST, I’ll post a ne...

I am installing 8 IP security cameras in our youth center, all are POE.  We do have plans to expand to more cameras in the future for outdoor coverage.  We currently have a 24 port switch (not POE) that we will be replacing, and I am either using a c...

cop by Level 1
  • 691 Views
  • 3 replies
  • 0 Helpful votes

Hi Team,I have a CISCO 7206VXR device and same is hitting on the below vulnerabilies. Cisco IOS Software TCP Memory Leak DoS (cisco-sa-20150325-tcpleak)--(CVE -->CVE-2015-0646)Cisco IOS Software Multiple Network Address Translation (NAT) Denial of Se...

Robo123 by Level 1
  • 995 Views
  • 2 replies
  • 0 Helpful votes

Hi folks,I'm facing the following problem on a cisco WS-C3750G-24TS vith the following configuration : IOS : Version 12.2(35)SE5 System image : c3750-ipservices-mz.122-35.SE5I configured the C3750 with "sdm prefer dual-ipv4-and-ipv6 routing" and made...

Hi, i am little confused as what is meant by burst size ?? and what is meant by traffic rate ? since traffic rate is measured in number of bits and burst size is measured in bytes so what i have understood is that, burst size determines the biggest p...

Hello, I see that by default, a 3750 switch only allocates 4% of output bandwidth for queue 1 i.e. EF traffic (see attached image).I am just interested as to why this percentage is so low compared to the other 3 queues which have 25%. Thank you.

Hey Cisco Goers. My first post here, thanks for the forums. Going to keep my question brief for now as it is pretty straight forward. Is there a way to gracefully move an IP address on an SVI from one VLAN to another without destroying the IP address...

Skawilly1 by Level 1
  • 1022 Views
  • 4 replies
  • 0 Helpful votes

Dear Experts, My name is Martin Botsov and I am a complete novice as far as Cisco WAN/LAN switching and routingis concerned as well as Cisco IOS. I've always wanted to have a Cisco router and recently anopportunity to replace my old Netgear FVX538 wi...

mocuZ by Level 1
  • 3848 Views
  • 2 replies
  • 0 Helpful votes

Hi, I have 3 x Cisco 2960 switches connected to each other via PAgP EtherChannels. This works today. I would like to add LACP EtherChannels to one of my 2960 switches to connect my VMWare ESXi (vSphere 6.5) host’s via teamed NICs. The current EtherCh...

AvdVyver by Level 1
  • 16436 Views
  • 10 replies
  • 0 Helpful votes

Hi, I am having difficulty implementing what should be an easy task. I have a single ESXi 6.5U1 host with 2 NICs teamed in a single vSwitch. The load balancing is set to “route based on IP hash”. As part of my troubleshooting I have also disabled bea...

AvdVyver by Level 1
  • 12755 Views
  • 15 replies
  • 0 Helpful votes

Hello all, I want to upgrade our nexus 3548x to the current suggested image 6.0(2)A8(4a. I've had a check of the impact of installation and got following: Compatibility check is done:Module bootable Impact Install-type Reason------ -------- ---------...

nssnas189 by Level 1
  • 1368 Views
  • 4 replies
  • 0 Helpful votes

hi Team, i have 7200 chassi in that where Gi6/0 interface is genarating High input errors. show int gi6/0 | i error2353591 input error,4695overrun,2348896 ignored kindly suggest on the above.

Robo123 by Level 1
  • 2805 Views
  • 15 replies
  • 0 Helpful votes

Hell all i'm so sorry, i'm not so good in english but i have a picture about my network and i don't know how to config sg500 dhcp and fix ip look like my the picture please, help me pleaseThank you all 

Unanswered Topics