Switching

Hi All, In VSS , I know that VSL is recommended to be 2 links at minimum and may be in different modules . Can we make both VSL Links in different modules where the sup engine is not one of them ?? We have a new VSS installation and the X2 interface ...

i have an ipv4 10.100.2.255 / 17 What is the subnet ID and the broadcast? Not able to understand the broadcast id, i believe it is 10.100.2.255, but for the cisco lab is 10.100.3.255.

usb port disabled after switch I upgraded upgraded switch from c2960s-universalk9-mz.150-2.Ex5 from 150-2.SE8.  Anyone know why? Is this a bug, feature, or if there is a way to restore functionality.

Hi guys, I have a routed port on our core switch and we are using that port to connect to another branch of ours through a point to point link. Here's the config. Its a 3850 switch. interface GigabitEthernet0/13 no switchport ip address 6.6.6.5 25...

In My ASR 920 router one port ge0/5 is connected to another device .0/5 is configured with bdi and in bdi ipv6 address is configured .I just wanna see what is exact command to see ipv6 address of the neighbour device .  Thanks in advance !!!!!

Can someone sanity check the below if possible. I simply want several interfaces on an ASR920 to be part of the same VLAN. The ports however are connecting to host devices so need to be untagged ports: ethernet evc VLAN101!interface GigabitEthernet0/...

Hello, I have a customer what has vlans that are sending hello packets for eigrp, I know is not the best practices, my question is, I need to trace and Ip and the trace is going via this vlan, how can I see what will the next hop be for this vlan. Or...

hi everyone, i have cisco 3560G switch. i am facing following problem. plz anyboby suggest me. what is problem, thanks in advance. Base ethernet MAC Address: 00:14:f2:09:47:00Xmodem file system is available.The password-recovery mechanism is enabled...

How do fix BRINGDOWN and POWER DISABLED problem on A9K-8T/4-B ios x 5.3.2 SMUs Installed see below the output KRP/0/RSP0/CPU0:ios(admin)# sh platform suRP/0/RSP0/CPU0:ios(admin)# sh platform summary lRP/0/RSP0/CPU0:ios(admin)# sh platform summary lo...

Hello! I have: cisco 7606s router, RSP720-3C-GE , WS-X6704-10GE , c7600rsp72043_rp-ADVIPSERVICESK9-M, Version 12.2(33)SRB2.Case: Server in LAN (192.168.1.8/29) connected to router's SVI 2 generates UDP broadcast (NetBIOS). Packet's headers are: SRC ...

We have been upgrading our infrastructure and replacing some older 10/100 switches with 10/100/1000. The original switches are mainly C3560-48 switching. The new switches we are installing are C3650-48TS-S switches. There was a couple items we notice...

I have the following configuration on my 3560 switch: track 1 ip sla 1 reachability delay down 20 up 20!ip sla 1 icmp-echo 10.78.243.7 source-ip 172.16.90.4 timeout 3000 threshold 3000 frequency 10ip sla schedule 1 life forever start-time now!ip rout...

We have a Catalyst 4506 (Sup V) and Catalyst 6509(Enhanced), both with 10GB ports capability. Since we bought them we haven't been able to connect both 10GB ports properly between two buildings. Both transceivers are X2-10GB-LR. Now, we are trying to...

Hello everyone Im trying to create a lab using GLBP for two different Vlans. I understand how it will work if i have a layer two switch in the middle between R1 and R2 but since i have a layer 3 switch between R1 and R2 and there is svi setup for ea...