Hi all, how to identify free module and submodule ports in cisco routers to ascertain the free bandwidth on them ? Chandrashekar G.
Hi all, how to identify free module and submodule ports in cisco routers to ascertain the free bandwidth on them ? Chandrashekar G.
During upgrade of two Nexus 3548 from 9.6.0.2.A6.2 to 9.6.0.2.A6.5a we got the following output: at006-core01# install all system n3500-uk9.6.0.2.A6.5a.bin kickstart n3500-uk9-kickstart.6.0.2.A6.5a.bin non-interruptiveInstaller is forced disruptive ...
Hello all,I have a SG500 switch. The port Gi0/19 is directly connected to a machine. When i show the running config file i find the following config in the interface gi0/19:switchport trunk native vlan 70 I need to understand this command because i'm...
I new install two 6807 and make a stack, now all of the VLAN work normal except VLAN1. I tried connect two notebook to same switch same LAN card to test speed. result is have packet loss and heave delay ( two notebook connect to VLAN1) i also use two...
Hello everyone, I have several vlans configured on two routers as sub-interfaces for each of my vlans. I'm able to ping sub-interface IP just fine between both routers except one vlan 240. If i shut the Vlan 240 down on router 2 i have no communicat...
Topology: Two routers, R1 (2951) and R2 (1921) are connected to a core stacked pair 3850. Currently, only R2 has an active WAN connection. It is cellular running BGP. R1, Core, R2 all run EIGRP. R1 doesn't have anything on the other side of it. (R1 ...
Hi, I have a ring topology with 8 siwtches , a switch core 3850 a 3850 and 6 3650 .All switches are connected by a two- port etherchanel Tengiga .The problem is that when you close the ring, a loop is created , and the entire network is coming down ...
Hi. I would be very grateful if anyone inform me where I can find the latest version of IOS that can be used in a switch catalyst model WS-C3548-XL-EN, the current version is c3500xl-c3h2s-mz.120-5.WC8.bin. Thank you in advance for information.
Hi All, I have the following configs setup on two switches. My question is if i have a layer 3 port channel setup on one end with channel mode ON, will I also need to bundle the other end? I did the below configs and it worked. The port channel came...
Hello I've try to find on cisco site the CE declaration for the Cisco 1921 without success. anyone can help me?
hi ,i can authenticate to vpn server , but i can reach any secured vpn subnets .note that i get an ip from pool and virtual template interface on router is getting up .but i dont reach any subnets from secured subnets !!!!!!!!!!!!!here is logs fro...
Dear All, I am running into an issue with an old IOS and EEM script as I can't make it bypass the AAA. So I have a script that should log into config mode and shut an interface if an event happens. Writing the script is not an issue. But to make ...
Hello, we are building a project and we have to choose different switches and routers from Cisco, to wire a 4-storey building (ground floor + floor 1 to 3). Each floor has 20 rooms, each with ten computers. On each floor, ...
We are replacing our mixed seven device L3 Core with two 6800's in VSS. I'm currently learning to configure VSS but I'm not sure if I need to do anything specific on both 6800 switches before enabling VSS, there seems little information on this. For ...
i was doing some hands-on labs and typed in "boot system tftp c2600-i-mz.123-9" to boot my router from a tftp server and when my router restarted it said that the file was to large to load into memory and my router kept restarting at that point as it...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-20-2025 06:31 PM | ||
05-20-2025 01:50 PM | ||
05-15-2025 09:37 PM | ||
05-06-2025 02:02 AM | ||
04-23-2025 06:26 AM |
User | Count |
---|---|
6 | |
4 | |
4 | |
3 | |
3 |