Switching

Hello, I was wondering about the best way to connect (10) SG200 Series Switches.  The basic layout is currently as follows: MDF: Watchguard XTM 505 Firewall Cisco SG200-50 (2)Cisco SG200-50P (1)Cisco SG200-26 (3)Cisco SG200-26P (1) IDF #1 Cisco SG...

Hi, We have 4 no of cisco 3750 switches in stack. Q.1 ) How to upgrade IOS of all 4 switches, by keeping them in stack... As per my knowledge one way is isolate them, upgrade ios, again add them in stack, which would be last way or lengthy procedure....

Currently dealing with a large amount of LandAttack messages on the ASA firewall.  Doing a capture on the ASA leads it to a SVI mac address on the core(4506).  I am trying to setup a monitor capture to catch all traffic going to the ASA on those cert...

Hi,  We are getting spike in high cpu utilization in cisco 1841: c1841-advipservicesk9-mz.124-9.T4.bin. Please check the logs and suggest further action. ------------------ show process cpu ------------------ CPU utilization for five seconds: 26%/...

Issue 1:  I have an internal Spiceworks webserver sitting behind a 5512.  I can't seem to figure out how to configure hairpin NAT using ASDM.  I'm not familiar enough with the CLI anymore to tackle it that way.  Additionally, initial requests are mad...

Hi people,  on cisco switches, I am trying to connect the output from ifHCInOctets  to the names of the interfaces via ifName and comparing it to show interfaces counter. I use the last number behind the period to build a relation: IF-MIB::ifHCInOc...

Please bare with me. I'm a newbie. I'm a junior entry level engineer. Migrating some devices from several smaller subnets /26 to a new /24 subnet. Senior engineers told me to have a plan to migrate these devices over since we won't be able to do thi...

Hi, We've recently sold a few SG220 series switches, 26 & 50 port versions. We have noticed that on ALL the switches we are getting "input errors" on the interfaces. GigabitEthernet27 is up  Hardware is Gigabit Ethernet  Auto-duplex, Auto-speed, m...

Hi All, Hopefully this is a fairly simple task for someone, we have a WS-C3650-24PS  running software 03.03.05SE cat3k_caa-universalk9 I have the following VLAN's setup: VLAN10 - 10.185.53.0/24 VLAN50 - 10.183.53.0/24 VLAN511 - 10.186.51.0/24 VLAN4...

Dear all, I tried to configure remote access VPN on Cisco router 1901, but it does not work. The interface tunnel 1 on router status is Up - Down. Could anyone please check my configuration file and help me to correct it ? Thank you all, Lam

1. Let's say I have 2 subnets , 192.168.1.0/24 and 192.168.2.0/24, i want to configure interfaces 0/1 to 0/12 to VLAN1 to cater for 192.168.1.0/24 and interfaces 0/13 to 0/20 to cater for 192.168.2.0/24, the traffic from VLAN1 can communicate to VLAN...

Hi,I've been looking through the data sheets and can't find a defintive answer to my question and was hoping someone might be able to answer it here.  Can the CAB-SFP-50CM be used with a compact 12 port 3650?Many Thanks,Hugo.

Hello all, I was wondering if someone could answer me the below log that i have noticed and i am not quite sure what it is.2016 Jun 22 13:42:12     %KERN-2-SYSTEM_MSG: eth0: MAC1 errors: tx_overflow=0 tx_parity=0 rx_parity=0 rx_fifo=0 - kernel Than...

Hi all,I have planned to change all oldest access switches with 2960X. On a test one, monitored by PRTG, CPU is always around 40% as the old 3560's are 8% CPU usage.Running the EX4 release. Does anyone have the same values ? This problem seems to be ...