Buy or Renew
Buy or Renew

Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

Labels

Forum Posts

Start a conversation

Resolved! Schudler problem

Hello we would like to get a periodical backup everyday in our data-center. We tried to use the feature schudler, but we always have problems with the script: cli var name timestamp $(TIMESTAMP) ;copy running-config bootflash:/$(SWITCHNAME)-cfg.$(tim...

VSS not reinstating after blackout

Hi gents,I'm deploying a pair of 4500X in VSS mode for a new customer.After preconfiguration phase and ascertaining I had a good VSS clustering in the LAB, I powered the pair down for final deployment but they would not come back up in VSS mode as ex...

Jorge F by • Level 1
  • 680 Views
  • 3 replies
  • 0 Helpful votes

Regarding C3750 outputs messages

Hi, When I configured "router bgp <as-number" on Cat3750, C3750 outputs "RT: add router 4, all protocols have local database" messages. /////(config)#router bgp <as-number>(config-router)#) RT: add router 4, all protocols have local database <---here...

Internet load balancing?

We have an MPLS network with 50 sites that connect to 2 central sites (SITE A & B) that are about 100 miles apart (see diagram) The 2 central sites (SITE A & B) are connected directly to each other via a 100mb link. One Central site (SITE B) has an A...

louis0001 by • Level 3
  • 467 Views
  • 1 replies
  • 0 Helpful votes

Resolved! 3750X showing unexpected log

hello everyone, one of the 3750x which is operating on our customers site is showing the log below log : %ADJ-3-RESOLVE_REQ: Adj resolve request: Failed to resolve 11.71.101.241 Vlan300 here is the info of the unit PID : WS-C3750X-24 VER : 15.0(2)S...

Resolved! STP port cost and Etherchannel

I have seen references that two bundled FastEthernet ports into an Etherchannel results in an STP cost of 12. How is STP cost of 12 derived when the port cost of a single FastEthernet port is 19? --> FastEthernet is 100 Mbps. I want to grasp and unde...

Default gateway??

Hello, I've this network where each of the 3 routers have 2 ports, one of them connected to a common network and other one to a separate network. The common network's ports are connected to a switch and the switch then connects to a host. On the sepa...

Resolved! IPv6 Default Route with outgoing interface

Hi all, I have my hands on the following scenario: P1R1 and P1R3 are connected through their respective FastEthernet 0/0 interfaces.The IPv6 address of the fa0/0 of P1R1 is 2001:0:1:1::1 (this will be the next-hop address of the default route) P1...

Resolved! Spanning Tree enabled only in one Switch

Hi everybody,  I have a question that maybe could be a silly question, but I have to ask it.  If I have a redundant topology and disable Spanning Tree on all the switches except one, what's the difference if I set Spanning Tree on all the switches? ...

Resolved! STP Loops

We had a trunk link go down on a switch due to the fiber cord being bent. I replaced the cord and wanted to add a redundant link just in case this happens again. When I added the second fiber to trunk link, a loop occured instantly. Once it was unplu...

bmack2121 by • Level 1
  • 764 Views
  • 4 replies
  • 0 Helpful votes
Load more