Hi All,I wanted to understand why switch wont form a Trunk if both sides are dynamic auto.I have done the simulation lab and can see even dynamic auto sends a negotiation message.Just wanted to understand what headers switch will check to make the po...
Forum Posts
Is there any way that we can decrypt type 9 secret on Cisco Switch to get Palin text Password
I have Cisco 9500/9300 and its connected to Juniper EX4400/QFX 5100 Series. Cisco is on Rapid-PVST and Juniper is on VSTP/RSTP. The Cisco and Juniper are on LACP. STP root bridge selection happen between Cisco and Juniper and configured Cisco to be...
So today I had an SSH session going to my ISR 3925 SEC/K9 running IOS version 15.7 and I suddenly lost the connection. When I tried to reconnect I received the error in Putty stating that the connection was refused. I quickly obtained a console con...
Hi, Peeps,I have a Cisco Catalyst 2960X and early today I upgraded the firmware, upon reloading, the switch did not boot anymore, I tried the following workarounds:1. Pressing the Mode Button for 15 secs2. Power cycling the switch3. Trying to do the ...
Does anyone know if there are any intermediary updates that are required to move from 15.2(2)E7 to 15.2.7E5 MD on a WS-C2960X-24TD-L?
Hello all,In terms of doing IOS-XE software upgrades, there are 2 ways to do it - the install mode way, or the request platform way. @Leo Laohoo has written some great guides for upgrading ISR models with request platform and upgrading Cat 9k models ...
Resolved! Stealthwatch Error 17.15.03
Upgraded this morning from IOS-XE 17.12.03 -> 17.15.03 (C9300-48UXM). I am now getting these messages in the logs:Apr 18 2025 08:45:34.943 CST: %IOSXE-3-PLATFORM: Switch 1 R0/0: fed: Stealthwatch Cloud is not initialized.Please configure to use this ...
We use many 9200 8 port switches with the micro USB-B console interface. Up till today, techs have been using a OTC micro USB cable to access the 9200 V01 switches for configuration. We attempted to configure a fresh from the box C9200CX-8P-2X2G-A ...
Resolved! DHCP vlan trouble
Hello, can anyone help me with a DHCP problem when I try to configure my PCs VLAN20 . This is for my term paper . I lost a lot of time trying to fix it myself. My computers are not getting ip addresses through DHCP and also I can't ping other vlans!
Resolved! Change fan direction C9500
I have a cisco model C9500-40X-A. Am i able to change the fan flow direction from " front to back" to "back to front" fans ?
Does the N9K-C93216TC-FX2 switch support SFP-10G-T-X?
Hi Amazing People here - please helpI am trying to upgrade my C9500-48Y4C switch from 17.09.04a to 17.09.06a but it failed everytime.I copied the new file to the flash - that worked perfectly fine.when I do install add file flash: XXXXXXXXXit gives m...
Hi everybody,I need to load an IOS from ROMmon-mode to a Catalyst 3550.Of cause I could do that via xmodem but I thought it should also be possible via TFTP.What I did:switch: IP_ADDRESS=192.168.1.1switch: IP_SUBNET_MASK=255.255.255.0switch: TFTP_SER...
ello Community,we have some issues concerning VRF and MAB that we don't understand.Our Platform is a C9500, network essential smart license.We use the Mgmt-interface gi0/0 for security reasons and a central radius server for authentication, which wor...
