ip nat inside source list 199interface fastethernet4overloadip route 0.0.0.0 0.0.0.092.208.96.206ip route 0.0.0.0 0.0.0.0fastethernet4!access-list 199 permit ip any anyno cdp run!please, explain each command line.thanks
ip nat inside source list 199interface fastethernet4overloadip route 0.0.0.0 0.0.0.092.208.96.206ip route 0.0.0.0 0.0.0.0fastethernet4!access-list 199 permit ip any anyno cdp run!please, explain each command line.thanks
Hi to all,normally this is a native VLAN mismatch behavior.A customer has connected some 3COM switches to a VSS and some of them, not all, show this error message and block two vlansThe configuration is ok. We have only trunk ports and the 3Com are s...
I have a client that has an HP infrastrucutre (I know... losers) but I am integrating a new Cisco core switch (3560X with 1GB module) and I'm curious if they can use their existing HP SFP - Part #: J4858B Will I be able to use this SFP in the Cisco s...
Hi Team, We have one Cisco 6506-E with SUP-720-3B installed at one Customer place.This Switch got rebooted and giving last reset from s/w reset. cisco WS-C6506-E (R7000) processor (revision 1.1) with 516096K/8192K bytes of memory.Processor board ID S...
Hi all ,Interface counters are not increasing in our cisco 3750 switch eventhough traffic is going on .we are running the below version:c3750-ipservicesk9-mz.122-53.SE2.binAm i hitting any bug or something i need to check ?Thanks,Regards,Vijay
I have a Cisco 4507R (Supervisor IV) that I need to upgrade the IOS on, and have decided to upgrade to 15.0.2-SG7 (ipbasek9). The current rom that is installed on the switch is 12.1(12r)EW; do I need to upgrade this in order to use 15.0.2-SG7? I beli...
I am plugging a device into FastEthernet 1/0/22. I cannot get DHCP across the trunk. Config is at link. Any ideas? https://www.dropbox.com/s/gsyai3e94s170hv/FRS.rtf
Hello,i want to reach a catalyst 2950 i connected to a 3560 catalyst. The 2950 is on switchmode trunk (dot1q) and the 3560 also. On the 3560 i can see details and the correct IP with CDP but i cannot reach them.IP of my 3560:10.138.128.3 /24IP of my ...
We have around 10 separate buildings all connecting back to the main server room over fibre connections. In each building on average we have 10 access switches and 1 Edge switch (Distribution layer but routing is done on our core switches) which we t...
Hello,I am trying to convert the 4 uplinks, by default at 10 gig to 4x 1 gig ports using:Switch(config)# hw-module uplink select? gigabitethernet Select the gigabit uplinks tengigabitethernet Select the 10G uplinks but the system doesn't r...
HiI need advise for how to do password recovery for 2911 The issue with me is how to send the break sequenceI tried using putty with setting > external commands > BreakAlso triedBreak on keyboardAlso tried Esc and Ctrl+CBut till now I can't access Ro...
Hello,please do you know the one config ACL that allows only allow the exchange of files between two hosts, (ptotocole TCP / UDP Port eq?)Best regards,
Hi Everybody, sorry in advance but i dont speak english as well as i want.Well my problem is the next, i want to configure ssh v2 in a switch 2960 series, i type the next.sw-apt#config tsw-apt(config)#ip domain-name whereversw-apt...
We have a 4510R+E which is configured as follows:Chassis Type : WS-C4510R+EPower consumed by backplane : 40 WattsMod Ports Card Type Model Serial No.---+-----+--------------------------------------+----------...
I have a customer that has several hundred cisco devices (switches/routers) that they would like to update all the passwords on. They currently have all their devices configured in Cisco Prime. Is there a way to push out new passwords via Prime wit...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-23-2024 10:41 PM | ||
04-23-2024 11:38 AM | ||
04-23-2024 09:53 AM | ||
04-23-2024 02:53 AM | ||
04-19-2024 05:58 AM |
User | Count |
---|---|
11 | |
10 | |
8 | |
7 | |
6 |