Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, November 4, 2024 through Friday, November 15, 2024. Our colleagues Rohit Chopra, Vaibhav Aggarwal, Anuraag Majumdar, Saquib Zeya...
Forum Posts
Can anyone tell me where there is a limit of 5 comma-serarated values in the 'interface range' command?
Hello, need help. I'm trying to allow Internet access from a newly created VLAN. NetworkUsing C1760 router for Voice T1, currently Default Gateway for Voice and Data.C1760 is configured with 2 sub-interface networks 10.1.1.x & 10.100.1.xUsing ASA5510...
We're currently upgrading our network from a flat layer 2 setup with a mix of HP, Dell, 3com, over to Cisco for the core and some HP for PoE/edge but we're running into trouble swapping in our first Cisco switch, a 3750x which has a bit of learning c...
Hello, this is a cross post from the Microsoft forums, so I hope that's OK. My problem is either a Cisco routing problem or a Windows 7 problem; I'm not ssure with which I have gone wrong:We are getting Events 5719 from NETLOGON with the message "cur...
Hello,A couple of days ago, suddenly my internet connection went down. I was not able to ping or access the router via telnet and ssh. The switch in my room showed a light of the port to the router, so the port on the router must be up.I reset the mo...
Resolved! spanning tree error
Hi,While keying in command: spanning-tree vlan 1-4096 priority 0, below error was received,% Command rejected: Bad instance list: Character #7 delimits a number which is 0I could not find any reference to this. Appreciate all help , what does this me...
Resolved! Switching Design for a big Network
Hi Everybody,I need to design the architecture for a big network (about 800 nodes)1-/ what is the core level in an archietcure and in what case we need a core level?2-/ for a big network with 900 nodes, wich switches can be used for Distributions Lev...
HelloIs it possible to terminate several MACsec connetions from different switches on a single switchport? This question refer to the Catalyst 3560X and 3750X switches.Does anyone know how is the performance on a 1 giga or 10 giga link with MACsec on...
Dear All ,I have few WS-C3560X-24 switches . Whether this supports MPLS tag switching ?? Can i use this as a PE router ? Currently I have lanbase license only , i just asked our sales to purchaise upgrade license C3560X-24-L-E . I want to run MPLS ...
Hi, We got %RFS-3-MSG_INCOMP: ifs_issu_get_msg_mtu(): msg_type [86] under session [721130] is incompatible error on 7613 router. As per Cisco The message types are incompatible under ISSU.Please suggest the criticality and why this comes. Regards,...
I am in the process of adding a automatic reset to our port security here on our campus. I believe the command I want to run is errdisabled recover cause psecure-violation errdisbaled recovery interval <time in seconds>The issue I am running into is ...
Resolved! single mac security
Hi,Following commands will be configured for allowing only one single mac (dynamic) to be used on a switch port fa0/1.switchport port-securityswitchport port-security violation shutdownso , in this case, if user A connects his laptop to fa0/1, he wil...
I have 6506 switch to which 2950 switch is connected.To 2950 a server is connected is there any easy method to track the ip of that server from 2950 switch.If so please mention the steps.
We are currently migrating hundred Catalyst 2950s to sixty-three Catalyst 4506. We decided to buy them because we need the high port density, power-over-ethernet and ipv6 features in the access layer.Last week we turned on the first five switches. Se...
Hi,Please I need some help with a vrf-lite deployment which is currently working ok at one of my sites. But the problem I am now facing is ho to tag some interesting traffic sourced from vlans within the two seperate vrfs I am using. The first proble...
