Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

I have a blade chassis with 2 blade switches (BS). Those blade switches run IEEE STP.They are stacked to each other.Each blade switch has 2 uplinks to one of 2 Cisco Nexus ToR switches. The NK5s are running vPC between them and PVST+The  N5Ks are dua...

visitor68 by Level 5
  • 959 Views
  • 4 replies
  • 0 Helpful votes

Trying to setup guest access for a WAP4410N. It is plugged into a PoE port on a Catalyst 3750G. Currently LAN access works over VLAN 100, and clients reach the DHCP server and get an IP.I have a 2nd SSID setup on VLAN 20 for guest access. I've setup ...

netguyz08 by Level 1
  • 2692 Views
  • 10 replies
  • 0 Helpful votes

Hi,Is it possible for DHCP services with same pool and range providing IP's to client in an environment where we have 2 Routers running HSRP.As i have many client IP conflicts, as the standby router also provides IP to the client. Shouldn't the activ...

ramarao by Level 1
  • 6659 Views
  • 6 replies
  • 6 Helpful votes

Resolved! Communication VLAN

Bonjour,J'ai dans mon réseau, un switch cisco Catalyst 3500 XL ou j'ai 3 ou 4 vlans. Voici la configuration du réseau :Mon routeur me sert de serveur DHCP, je voudrais que tous mes vlans (ceux du switch et ceux du serveur VMware) obtiennent leurs par...

Xzap61170 by Level 1
  • 1386 Views
  • 2 replies
  • 0 Helpful votes

HiProblem: I have a analog door phone connected to a port in my FXS card in my 2911 gateway. The gateway is an MGCP gateway running on a CUCM BE ver. 7.1The PLAR functionality is working and the expected IP phone is ringing but when i hang-up the IP ...

Hi ExpertsI am Using Cisco 2350 Switches in my LAN. I want to enable port security on Cisco 2350 Switch. But port security commands are not supported under interface configuration. Cisco 2350 switch having only LAN Lite image. I wanted to know whethe...

jojiv by Level 1
  • 487 Views
  • 2 replies
  • 0 Helpful votes

Has anyone ever configured a non-Cisco switch, that only runs the IEEE version of STP/RSTP, to interoperate with a Cisco switch running PVSTP+/RPVSTP+? I am trying to configure a Dell Power Connect blade switch to interoperate with a Cisco Nexus 5000...

visitor68 by Level 5
  • 7634 Views
  • 14 replies
  • 0 Helpful votes

Hello All Friends,We have just finish configuration on Cisco 1861 router, but i am unable to browse Internet even on router can any one suggest me.My physical connection are as per Attached snap, also you can refer my attached configuration. I want t...

Hello all.  I am trying to figure out how to create a Etherchannel bundle on two 3524 switches that i have.  I have tried to follow this link but i am not sure it is working or not and if i am missing any commands.http://www.cisco.com/en/US/tech/tk38...

Based on the way my network is configured, I am unable to connect one of my servers directly to a firewall for a DMZ.  I wanting to allow anything coming into the server, but deny where it can go.  For example...Coming from the serverPermit traffic t...

ngthen by Level 1
  • 596 Views
  • 3 replies
  • 0 Helpful votes

Resolved! ACL PROBLEM

Hello,I have a CISCO 1841 ROUTER (IP=192.168.1.250) and a CATALYST 2950 SWITCH (IP=192.168.1.251) in my test LAB.Both are connected with a TRUNK , to share the same VLANS.The problem is , when I connect to VLAN 10 or 20 or 30 , I am not able to PING ...

Yeah, that's pretty much it.But to elaborate, we have a few 5-switch stacks, with a 10gb uplink in switches 1 and 5 connecting back to a pair of 6506's... one in T1/1/2, the other in T5/1/2.  The NM's are C3KX-NM-10G's, which provide 4 ports, the des...

mikearama by Level 1
  • 4746 Views
  • 1 replies
  • 0 Helpful votes