Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, November 4, 2024 through Friday, November 15, 2024. Our colleagues Rohit Chopra, Vaibhav Aggarwal, Anuraag Majumdar, Saquib Zeya...
Forum Posts
HelloWe have a single Vlan made up of a number of access switches and three 6509 switches. Predominantly the traffic is all Multicast and it is very high. When a multicast packet appears on the network, it is multicast to every port within the Vlan. ...
Hello,I need to disable the keepalive on two gigabit uplink ports.Can anyone tell me what commands i need to use exactly to disable keepalive on GigabitEthernet0/1 and GigabitEthernet0/2VMINFswitch>enableVMINFswitch#configure terminalVMINFswitch# ....
I was recently successful in testing an inbound ACL-based QoS policy on all 24 ports of a Development 2960 catalyst switch. The policy marks DSCP values base on access-list classification. The access-lists in the policy reference layer 3/4 criteri...
why we require cross over cabla to connect pc to router? is it related to DTE/DCE concept,if yes then please elaborate in which cases router acts as dte n dce?thankinh u.......
How do the WS-CAC-6000 power supplies interact with each other and the chassis if one power source is on UPS of each power supply and the other power source is on normal street power? Can a power spike from the non-UPS side carry through onto the oth...
Hi,I have 3 Router connected via Serial interface i.e. R1 , R2 and R3 now I want to Network Advertise in unicast from Router R1 to R3 without using following things how I can do pls help me..neighbor command/ PBR/ Static or Default Route/ Redisributi...
Dear all,I would like to upgrade 6509-E switch with (s72033-adventerprisek9_wan-mz.122-18.SXF17a.bin) does it support the FWSM Firewall : Version 3.2(3), IDSM : Version 7.2(1) and LOAD BALANCE : Version 3.0(0)A1(4a) please let me know it's URGENT.Th...
My 3750 stack running ipservicesk9-m 12.2(53)SE is heavily loaded at times, and the log shows that it is the snmpengine that causes the load.%SNMP-3-CPUHOG: Processing GetNext of lldpRemEntry.6.0and that this task has been running for some time and t...
Cannot connect on 22 port through PAT on router. I have next schema:In log on ASA:In log on Router:*Aug 6 08:54:36.602: IP: s=5.5.5.6 (GigabitEthernet0/0), d=10.10.10.254, len 60, input feature*Aug 6 08:54:36.602: TCP src=44763, dst=22, seq=407...
POST: PortASIC RingLoopback Test: BeginTCAM (asic:3, bit:5) address bus test failedFrom what is it getting in mistake?what deffect is it in it?_____________________________RegardsBayasgalan.B
Hi !7606/Sup720-3bxl/12.2(33)SRC4. A huge traffic is observed from fabric to Sup, but there are no active ports on Sup. What is the traffic ?7606-3#sh platform hardware capacity fabricSwitch Fabric ResourcesBus utilization: current: 10%, peak was 21%...
Hi!Let me describe the task first.Our company Intranet consists of 2 regional networks, each of which is a DMVPN network with regional center (regional hub, Cisco 1811) and small branches (spokes, Cisco 871). The hubs of the regional centers are also...
aside from doing in-line taps, i'm curious to see what people are doing to get around 2 session limit. I have need to monitor multiple source vlans and it's over-subscribing the destination port. also using vlan and physical interfaces as a source in...
Resolved! ACL not working
Hi all,I have two 2960 cisco switch and 1 cisco catalyst 3750.I configure the 3750 as the main core.Here's the configuration:interface GigabitEthernet1/0/1 switchport trunk encapsulation dot1q ...
I have found the following question:Which feature is required for multiple VLANs to span multiple switches?a. A trunk to connect the switches.b. A router to connect the switches.c. A bridge to connect the switches.d. A VLAN configured between the swi...
