Buy or Renew
Buy or Renew

Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

Start a conversation

Resolved! QoS class issue

I have a QoS issue. Please help me figure out. ip access-list extended SILVER-TRAFFICpermit tcp any  10.0.0.0 0.255.255.255 eq 80ip access-list extended BRONZE-TRAFFICpermit tcp any  10.3.115.0 0.0.0.255 eq 80permit tcp any  10.60.52.0 0.0.0.255 eq 8...

cscyangyu by • Level 1
  • 627 Views
  • 2 replies
  • 0 Helpful votes

Storm-Control on X6704-10GE

Since storm-control on 10G interface was enabled, following message began logged in syslog.>> %PM_PLATFORM-5-PORTDROP: Port TenGigabitEthernet1/1 dropped packets due  to storm controlThere is no application using broadcast or multicast, so ifInBroadc...

Resolved! how to configure GLBP works as HSRP

My company want to use the GLBP to load balance the traffic , but for some reason , We want to configure the GLBP work as the HSRP , make 2 router 1 active and another is standby . Does anyone know how to configure the GLBP works as HSRP?

cscyangyu by • Level 1
  • 638 Views
  • 1 replies
  • 0 Helpful votes

Buffering

Hi Experts,We have a client on lease line connectivity. Earlier connected thru Serial leased connectivity and now migrated on Ethernet connectivity (i.e Earlier WAN connectivity was on Serial interface @ client router and now shifted on same router's...

Tools convert CatOS to IOS

Hi, have you a link or tools to convert CatOS configuration to IOS configuration on Cat 6500 ?.Old link to http://www.cisco.com/cgi-bin/Support/CatCfgConversion/catcfg_xlat.pl is bad or removed.Thank'sMR

mrobert by • Level 1
  • 5117 Views
  • 2 replies
  • 0 Helpful votes

3750 DHCP Configuration does not save

I have a 3750 configured as a DHCP server.  I saved the configuration to nvram, however, every time I power cycle the switch the DHCP config disappears (everything else is saved properly).  I have verified that the startup config contains the DHCP co...

Resolved! Differences between PFC3A and PFC3B

Hi,Can anyone point me at the documentation that details the functional differences between a PFC3A (on a SUP720) and a PFC3B?The current docs (http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps708/product_data_sheet09186a0080159856.html) ...

mjoc27x by • Level 1
  • 6963 Views
  • 4 replies
  • 0 Helpful votes

Resolved! HSRP Tracking

Hi,What is the purpose of interface tracking in HSRP? How it works? Will the normal HSRP works if tracking is configured?

drnteam by • Level 1
  • 1760 Views
  • 6 replies
  • 0 Helpful votes

2960 switchport trunk

I am connecting a 2960-24LT-L to a 3750 via a Gigabit Ethernet port.  I have run the cisco-switch macro on my 2960 and I noticed it did not put the encapsulation dot1q after the switchport mode trunk command.  The Gigabit Ethernet port on the 3750 th...

fasteddye by • Level 1
  • 10205 Views
  • 6 replies
  • 0 Helpful votes

Inter-Vlan browsing problem

Hello and thanks for reading my post,I've just configured two different VLANs (plus the default one) in my 3560G switch, I can ping from any VLAN to any host in other VLANs, but I cannot see the computers, do you know why?.I created the VLANs to isol...

View All
Review Cisco Networking for a $25 gift card