i am trying to configure NAT with overloading option.we have 16 static IP from the ISP, we use most of them as static nating for our servers.we need to use one or 2 static IP addresses for all the users to connect to the internet (NAT + overload).i h...
Hi ,i would like to configure QoS on 3750 switch, so that i can reserve 50% b/w for voice and 50% for data.regardsNeo
Hi,I successfully stacked 2 3750's and they have been fine for a few months. I used a stack cable from stack port 1 to stack port 1 on the other switch, but today I was told that is wrong it should go from stack port 1 on one of the swithces and con...
Hello Experts. I currently have 3 x 3750 switches that are connected in a Circle and provide the Same VTP domain over 3 physical locations.Each Switch is a VTP server and at the moment I have the 3 swicthes setup utilising Etherchannel load balancing...
HiI need some help to login on Standby module, to reload standby module and get Sh tech and other information from the standby module.Thanks in advance.RegardsJagdev
I have a catalyst express WS-CE500-24TT switch which is serving the connecting for several VM machines (SUN Solaris zones) .I have trouble with the connection of these virtual servers to the catalyst, since the catalyst identifies the functions of th...
Hiin our org we have 6509 has the core switch but it as not gateway because our gateway to the internet is thru a proxy server. but we have another connection outside if we want to use static routes. But since static routes is for destination, i want...
My network layout:internet>cisco1841>asa5510>4006>networkFrom the 1841 I can ping outside I can ping the .193 and .194 address. I cannot ping the inside network 192.168.100.0.From the Firewall and the Network I can ping the .170 the .193 and .194. I ...
Dear All,I have cisco 3560G-TS-S with IOS 12.2(35)SE5 IPbase software. I have vlan 1 and vlan 2.Each Vlan has one pc attached to it. Each pc can ping its default vlan ip address and can ping the router behind the swtich.The problem is pc 1 can not pi...
Hello,Has anyone experience this.. I have a Cisco 6513 with 4x1gb interfaces going to a Fortigate firewall. We have added all interfaces to channel-group 256.However a "show etherchannel 256 detail" shows a etherchannel 256 and 256A?????If I look at...
Hi all,I know to convert bytes to KB we divide by 1024 and then to convert it to MB we divide again by 1024.Correct we if i am wrong is there any other easy way that we can do thismany thanksmahesh
Hi,i have a Layer3 1 gig ethernet interface on to which a 10Mb link has been terminated, i would like to configure QoS on the interface so that whenever the utilization reaches 10Mb it started shaping trafic. Please helpregardsNeo
Hi friends,i am saravanan from Bangalore. I have one cisco 3560 switch and some L2 switches also.i want to create inter vlan routing in the 3560. I already tried to enable ip routing command.Then i tried to create routing protocol also.so please give...
Hi Folks,While configuring L3 EtherChannel on NME 16ESW module I am not able to get "Channel-Group 1 mode on" command.I am easily able to make L2 EtherChannel. I am using 12.4 (12) IOS. Kindly have a look at the below configurations:R0(config)#int p...
Hi,My switch stack is running a 48port POE 3560 switch, switch 1 and 2 are setup as Layer 3 and the rest are Layer 2. I'm running C3560-IPBASE-M Version 12.2(25)SEE3 I have read that my 3560 POE switch does not support Netflow. Is there an alternativ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 09-03-2025 11:45 AM | ||
| 07-08-2025 11:44 PM | ||
| 07-04-2025 02:13 AM | ||
| 06-26-2025 10:05 AM | ||
| 06-16-2025 07:47 PM |
| User | Count |
|---|---|
| 8 | |
| 7 | |
| 7 | |
| 5 | |
| 5 |
