i want to upgrade 6506 chassis as its full with module what will be the best replacemet cisco 6500 vss or nexus.module installed1) fwsm2)10G 4 PORT3)UTP 484)sfp 485)TWO SUP 720
i want to upgrade 6506 chassis as its full with module what will be the best replacemet cisco 6500 vss or nexus.module installed1) fwsm2)10G 4 PORT3)UTP 484)sfp 485)TWO SUP 720
i just upgraded all of my switch links from l2 to l3 /30's and now my entire routing table is on all of the l3 switches. i ran the command ip summary-address eigrp 100 0.0.0.0 0.0.0.0 on the interface but i lose connection to the switch. I'm trying t...
hi! we have cisco catalyst 6500 and i have noticed strange line in logging auth-event (gi*/*) link down auth-event (gi*/*) link up what does it mean? and how to understand what was the reason of this line to appear.
Hi, I am having problems routing on our LAN. I have configured vlan in one network and need to use one of these port on another switch on another part of the network.++++++++++++++++++++++++++++++++++++++++6509_1 core_distrib3750 access_1 (can access...
Hi People,My 2950 switch's system bulb is blinking in green color whereas other bulbs in mode off. The ports which cables are connected in amber color.When I telnet into it the prompt gives like the following (switch:)and it says "bootin error".Wt co...
We have a 3560 switch that locks up (lighs full on with no variation). The only solution is to remove power. Is a typical symptom to a known issue??
Hello,Were can I find brief info on what CRC, input errors, output errors, runts, giants, throttles etc mean?Collisions I think would mean duplex issues what are late collisions?Thanks
I hope I posted this in the correct forum. I'm re-doing my network and I have a 2621XM router that's handling my internet traffic with some decent access-list, but I want to use my PIX for my firewall since I don't have enough flash to upgrade to 12....
Hi,Currently we have to write a document where it will be specify norms about our telecom infrastructure outside of our datacenter it-self. the scope of this documents will start at the user's computer desktop will pass by telecommunication and will...
Hi,I am wondering can I connect two networks over Cisco 876 router?I have set Vlan 1 with ip address and made command âaccess switch vlan 1â on FastEthernet 2.I have set Vlan 2 with ip address and made command âaccess switch vlan 2â on FastEt...
I have tried to configure ssh on 2611 router but there is no 'crypt key generate rsa' command in global configuration mode.Hear is the result of 'show version' command. Any ideas why? ThanksCisco Internetwork Operating System SoftwareIOS (tm) C2600 S...
Hello,we have several cisco ce520-24pc-k9 access switches that all have two uplink connections to two HP Procurve 54012zl edge switch (one uplink to every HP switch).But the ce520 is standard using PVST+ as a spanning tree protocol, but the HP use Mu...
Hi,please tell me the difference or similarity between GRE and IPSEC tunnel.Can they both be used for same purpose.Thanks,
Hi, we just have a new 2851 router come in and I powered it up. howerver after initialing the memory checking, it goes not go any anywhere? any idea ? it's brand new, just out of box. thanks
Hello,I'm using NAT with overload to translate IP adresses from a small office into an IP adress from the main office. The connection from the branch office with the main office is OK and the NAT is working, but the connection between main office and...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-23-2025 01:45 PM | ||
07-08-2025 11:44 PM | ||
07-04-2025 02:13 AM | ||
06-26-2025 10:05 AM | ||
06-16-2025 07:47 PM |
User | Count |
---|---|
13 | |
11 | |
9 | |
5 | |
4 |