Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, November 4, 2024 through Friday, November 15, 2024. Our colleagues Rohit Chopra, Vaibhav Aggarwal, Anuraag Majumdar, Saquib Zeya...
Forum Posts
Resolved! Fibre Optic connectors
Hi,could someone tell what the differences are between MTRJ and SC connectors?
I m having serial interface s1/1 with 10.205.250.9. Last 1 week i m getting frequently leased line down.. Whenever my leased line goes down both interface and line protocol goes down. I m running ospf protocol .. I have attached the log file.. can an...
Hi all,i have tried converting my 6509's existing CatOS {version 8.4} to IOS {12.2}, following the manual process. the 6509 has a Sup2 & an MSFC2.When i was done uploading the IOS & restarted the switch, the switch would boot normally, but the RP wou...
Hi,I have a Cisco 3725 router connected to our ISP (see diagram). It has a 16-port 10/100 Etherswitch (NM-16ESW). The f0/1 goes to a Cisco 3750 switch and our Internet connected servers are connected to the Cisco 3750 switch.What I would like to do ...
Hi All,Cisco switches have the ability to autonegotiate the speed and duplex settings. Does this ability depend on CDP? Do we need to enable CDP to have this autonegotiation functionality running?Cheers,Sharjeel
I have a Sup720. At boot up it (SP) says:System Bootstrap, Version 8.4(2) ReleaseCopyright (c) 1994-2005 by cisco Systems, Inc.Testing lower main memory - data equals addressTesting lower main memory - checkerboardTesting lower main memory - inverse ...
Hi,I have configured core sw as root bridge for VLAN 64 (4096).Core sw config:spanning-tree vlan 64 priority 4096I have checked the root bridge for VLAN 64 from access switchACC-SW1#sh spanning-tree vlan 64VLAN0064 Spanning tree enabled protocol rs...
Resolved! C6513 Supervisor 2 Backplane Utilization
The cisco C6513 core switch in the network here is giving the following readout:#show catalyst6000 traffic-meter traffic meter = 100% Last cleared at 09:26:41 CET Fri Nov 14 2008 peak = 100% reached at 10:00:31 CET Fri Nov 14 2008...
Hi,I have cisco 6509 switch with one sup720 engine. I have installed one 24 port fibre module,four 48 port normal Coper module & three 48 port POE modules.My problem is: On all the three POE modules i have connected IP phones out of which phones on t...
The LAN consists of two Catalyst 6500 switches running HSRP over a dual L2 port channel.Eigrp protocol is running between the core switches and WAN router.What configuration solution can I apply to provide redundancy between the core switches and the...
Resolved! not able to reset the password on 2610
I am trying to set up my old lab.. forgot the password. could not recover it.. I have Hp laptop with tera_term when I restart the router , I do BREAK no luck. I do ctrl+ breack,, no go.. any help please .. Thanks
HiIs it possible to create bandwidth policies based on VLAN ID ? What I try to figure out is to police the data send over an ethernet trunk. Voice needs to get 30% of the available bandwidth and the rest is for data. This must be configured on a Dot1...
Resolved! seting up a lab
HiI set up a loopback0 as 192.168.22.2 /16and when setting up a s0 w/ 192.168.22.3 /16 . I get labr1(config-if)#ip address 192.168.22.3 255.255.0.0192.168.0.0 overlaps with Loopback0now I did chng loopback0 to 1.1.1.1 and I and I am ok , but just nee...
Hi all, can someone possibly answer these questions I have, I have been reading my cisco icnd 2 book, But I am still unsure of a few items.1, When ospf starts, and forms a neighbour relationship on a lan with other routers, does each router only send...
1.When a frame is created by the datalink layer; where is the source and destination IP address located? I know the source & mac address is visible.2.Also I dont quite understand what happens at/with the ETHER-TYPE FIELD???3.What role does the protoc...
