Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, November 4, 2024 through Friday, November 15, 2024. Our colleagues Rohit Chopra, Vaibhav Aggarwal, Anuraag Majumdar, Saquib Zeya...
Forum Posts
Is it possible for both a 2950 switch attached to a 3700 router to restrict multicast flooding? The switch has IGMP Snooping enabled and the router has RGMP enabled, but not the switch, since it doesn?t support it. I don?t want all router and switch ...
Hi,I'm not sure if this is the right forum to post this question, but I couldn't find a more appropriate one...I have a Cisco 6509 running CAT OS v8.4(4) experiencing some periodic high CPU utilization. The period is ~30 minutes and it reaches 100%! ...
Hello Experts!i have to Design the following setup: 10 access-switch connected to the core(4507R)via L2 Trunk;the Network it is 100.4.0.0Switch 1 on vlan 50Switch 2 on vlan 51Switch 3 on vlan 52Switch 4 on vlan 53Switch 5 on vlan 54on the CORE:INT vl...
I have taken over a relatively simple network which has 2 cisco catalyst 2950 switches with 48 ports each. these are full and i need to add another switch to the network can i add a Cisco Catalyst 2950SX Switch with 24 ports? if so could someone plea...
Hello, I have a simple questionWhat is the difference in having many ports in a single switch and having multiple switches with less portsI can understand the difference, if you have all the ports in one switch you are placing all the eggs in one ba...
Hi all, I have heard svlan's mentioned, Can anyone tell me what they are ?
Resolved! DHCP Server on 3550
Hi all,I have Cisco 3550, i wan to configure DHCP server on same.i have done following configurationip dhcp pool LAB_N/Wnetwork 172.168.1.0 0.0.0.255default-router 172.168.1.100dns-server 202.x.x.6service dhcpis that all or i still need to heve more ...
Hi all, can anyone clarify this for me, If I have say 2 vlans on my network, can spanning tree be forwarding on an uplink port say for vlan 2, and be blocking for vlan 3 ? and would the port light be showing as orange, or as green as its forwarding ...
Got 2 switches connected together as follows port f0/26 on a cisco WS-C2950C-24 to port g0/48 on a cisco WS-C2960G-48TC-LThey are auto sensing speed and duplex and I cannot find a command to tie them down.The problem is that WS-C2950C-24 is auto sens...
Hi , I am unabel to find the Command conversion tool from CatOS to IOS on a 6509 CAT base switch.Kindly helpregardsNeo
Resolved! 4507R (Power suply)
HI!I Need link regarding 4507R Including power(Power suply) calculation10xsRegardsAli
Dear,I have three fibers coming from the different different locations on the same location. I want to active three links. When one link is goes down the network is up from the other link.
Resolved! Refurbished Router
HelloIs there any site in Cisco that will tell me if a router that i have purchased is refurbished or no?
Resolved! Multicast woes
Hi allI have the following very basic setup Router 1 - 2800_labinterface GigabitEthernet0/1 ip address 10.5.1.1 255.255.255.0 ip pim dense-mode duplex full speed 100endRouter 2 - 2600_rtr2 interface FastEthernet0/1 ip address 10.5.1.2 255.255.255.0 i...
Hi,I have 4 CE500 and 1 2960G. I would like to know an example of a good connction configuration. Right now my setup is far from optimal because I had some problems. For some reasons I could not have my IP phones to register with the Call Manager i...
