For a number of our gateways we are using snmp to monitor Active Calls; however, we are in the process of upgrading some of the gateways to the ISR 4400 series. On the older gateways we were using CISCO-POP-MGMT-MIB, but that doesn't seem to exist o...
Forum Posts
Hi Team , We have Catalyst 6509-E model , We just want to know how to read end of life and end of life support contracts . https://www.cisco.com/c/en/us/products/collateral/switches/catalyst-6500-series-switches/eos-eol-notice-c51-743096.html
Hello Experts , How to check if the switch is configured with SNMPv3 or SNMPv2c ?
As per attached diagram , CSR is receiving 6.6.6.6/32 from R6 as BGP external route.CSR belongs to AS number 500 and R6 is belongs to BGP AS number 600.Router#sh ip route 6.6.6.6Routing entry for 6.6.6.6/32Known via "bgp 500", distance 20, metric 0Ta...
Resolved! Line Card per-slot bandwidth
Good day, I would like to ask help in clarifying/verifying my current understanding of the line cards or in itself the switches/routers. For example I have a 4506 Switch and it is using the WS-X4548-RJ45 line card. Basically the WS-X4548-RJ45 has 48 ...
Hi allIs it possible to configure multiple VLAN (Voice VLAN , Data VLAN) in same subnet which is used for Cisco UC? If so, any configuration example? and also any critical performance issue? Thanks! Hugo
Hi Myself Muhit, How can I make a new native Vlan where I have already configured another native vlan. For example, I have created 4 vlan in each of my 3 switches. In Switch1, I made vlan 10 as native vlan and in SW2 & SW3, I made vlan 6 as native. t...
There is a limitation when going from 3.X to 16.3.5 Denali because of the 3.Xe boot loader being unable to boot a file more than 500MB from the flash.I cannot get 3.6.4E to update to Fuji 16.9.8. That OS file is only 429MB so that limitation should n...
Hello Experts , which memory output are we suppose to monitor ? output of "show platform software status control-processor brief" or output of "show memory processor statistics" Solarwinds shows used memory is 83% ..So it is taking the value from ...
Have a Cisco 4221 router with two NIM ES2-8 Switch modules and need help setting up the router so that I can pass data from one NIM ES2-8 Switch module port to the second NIM ES2-8 switch module ports.
Resolved! QoS DSCP Classification
We are not using cisco phones so the trust boundary is set at the access switch. Per the cisco QoS guide: Classification is enabled only if QoS is enabled on the switch. By default, QoS is enabled on the switch.During classification, the switch perfo...
Hi Experts , From the below output what does 1-RPO means ? does this shows the ROM or RAM output ?
Hello, I'm hoping someone could shed light on why is SG550XG-8F8T switch reporting 469 interfaces: # snmpwalk -v1 -c ******* $switch_ip_address .1.3.6.1.2.1.2.1 IF-MIB::ifNumber.0 = INTEGER: 469Interfaces status on the switch itself (starting from 16...
Good morning everyone! I've got a question regarding the following IE 2000 Industrial Ethernet Switches:IE 2000-16TC-G-EIE 2000-8TC-G-EI downloaded the latest IOS software "ie2000-universalk9-tar.152-8.E.tar" in order to get the gsd files which i nee...
Hello Experts , Output of "show version" shows that the switch has 1.98GB of memory. However, I see with "show memory" that the whole total memory between Processor, I/O and Driver is 538MB . what is the actual difference between physical memory a...
