Hi Everyone..Have a good day.. I am testing XRV 6.1.3 with the OSPF routing protocol as below in the topology. R1-R4 connection is considered. When I do "show IP route" and "show cef 4.4.4.4/32", it shows both routes but when I trace to 4.4.4.4, it o...
Hello everyone,I just finished my MPLS configuration but I have one last roadblock. I can reach my HQ LAN(10.10.1.0/24) from my branch but HQ cannot reach branch LAN(10.10.3.0/24).This happened after I did NAT outside and NAT inside on the branch rou...
on both switch HSRP for SVI interface for vlan 22 is keep on flapping below configuration as follows SW1#interface Vlan22ip address 10.29.44.2 255.255.255.0no ip redirectsstandby 22 ip 10.29.44.1standby 22 preemptstandby 22 authentication md5 key-ch...
Hi, I know that Auto-MDIX On or Off can be verified by "show controllers ethernet-controller gigbitethernet 1/0/x phy”. I'd like to know how to verify MDI/MDIX status of auto MDIX port on Catalyst2960X.
How do I configure a vLAN as the native vLAN for the SG350X switch using the GUI? (if possible, otherwise command line is fine) I want to create a trunk that contains all vLANs to connect the physical switch to a Nutanix cluster (4×1Gb x 4 hosts, us...
HI all, I've noticed, and read that a /22 subnet in an not to large network should be fine.But it got me thinking about what are the best practices when you take the amount of switches in a broadcast domain in account. For example (in this case an re...
We have a dual 6509 core running VSS. We have many access switches with dual uplinks in a port channels. The access switches are a mix of HP, Avaya, etc across multiple buildings of 3-5 floors each. 2 access switches tacks on each floor. 2-3 times a ...
Hello Cisco Community, I having a big issue with the connection between a cisco WSC3560 and cisco SF350.Both switches are blank (no config) but i am unable to ping from one switch to the other... The topology is quite easy i have one computer connect...
Hi Friends, I am looking for EOL & EOS date for Cisco Model WS-C2960X-48LPS-L and need to find other bulk of devices. Could you please share me suggestion how to find this.
Hello Community I'm trying to figure out if we can use 802.1x on meraki switches that can use machine certificates to authenticate via radius. According to this official document, switches can only authenticate using domain credentials, MAB or hybrid...
Hi,I would like to add 129.20.199.0/24 and 130.20.199.0/24 to the policer in the aggregate-policer ap-lala-d on c7600 that i have set now.After consulting the documentation, I found the following three solutions. Please help me to see if it is feasib...
Hi All, Create a privilege 7 user and added these permissionsprivilege exec level 7 terminal length 0privilege exec level 7 show running-configprivilege exec level 7 show startup-config when running Show running-config there is not much output but ge...
Hi, does anyone can explain what is MACSEC-256? I am not able to find any document provide explanation for MACSEC-256. Thank you.
Is SPA-5X1GE-V2 compatible with ASR1002-X Router?As per the Data Sheet it is compatible with Cisco ASR 1000 Series Router. I have verified it in ASR1002 and its working.But when I insert the SPA-5X1GE-V2 card in ASR1002-X Router, the card is not gett...
Please help how to add object group. I can add object group and add into ACL on 6500 model. but I couldn't add "object-group ip address" on 7600 model. -6500 model.object-group ip address DENY01[IP address] [Netmask]exitip access-list extended OUT100...
