When i switch on my router,i am getting this error...what is an issue
System Bootstrap, Version 15.0(1r)M15, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2011 by cisco Systems, Inc.
Total memory size = 2560 MB - On-board = 512 MB, DIMM0 = 2048 MB
CISCO2921/K9 platform with 2621440 Kbytes of main memory
Main memory is configured to 72/72(On-board/DIMM0) bit mode with ECC enabled
Readonly ROMMON initialized
program load complete, entry point: 0x80803000, size: 0x1b340
open(): Open Error = -66
boot: cannot open "flash0:"
boot: cannot determine first executable file name ondevice "flash0:"
System Bootstrap, Version 15.0(1r)M15, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2011 by cisco Systems, Inc.
Total memory size = 2560 MB - On-board = 512 MB, DIMM0 = 2048 MB
CISCO2921/K9 platform with 2621440 Kbytes of main memory
Main memory is configured to 72/72(On-board/DIMM0) bit mode with ECC enabled
Readonly ROMMON initialized
Compact Flash1: Not present
System Bootstrap, Version 15.0(1r)M15, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2011 by cisco Systems, Inc.
Total memory size = 2560 MB - On-board = 512 MB, DIMM0 = 2048 MB
CISCO2921/K9 platform with 2621440 Kbytes of main memory
Main memory is configured to 72/72(On-board/DIMM0) bit mode with ECC enabled
Readonly ROMMON initialized
program load complete, entry point: 0x80803000, size: 0x1b340
open(): Open Error = -66
boot: cannot open "flash0:"
boot: cannot determine first executable file name ondevice "flash0:"
System Bootstrap, Version 15.0(1r)M15, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2011 by cisco Systems, Inc.
Total memory size = 2560 MB - On-board = 512 MB, DIMM0 = 2048 MB
CISCO2921/K9 platform with 2621440 Kbytes of main memory
Main memory is configured to 72/72(On-board/DIMM0) bit mode with ECC enabled
Readonly ROMMON initialized
rommon 1 > DEV
monitor: command "DEV" not found
rommon 2 > dev
Devices in device table:
id name
flash0: compact flash 0
flash: compact flash 0
flash1: compact flash 1
bootflash: boot flash
usbflash0: usbflash0
usbflash1: usbflash1
eprom: eprom
rommon 3 > dir flash0:
program load complete, entry point: 0x80803000, size: 0x1b340
open(): Open Error = -66
dir: cannot open device "flash0:"
rommon 4 > dir flash:
program load complete, entry point: 0x80803000, size: 0x1b340
open(): Open Error = -66
dir: cannot open device "flash:"
rommon 5 > dir flash1:
dir: cannot open device "flash1:"
rommon 6 > dir flas dir eprom:
getdevnum warning: device "eprom" has size of zero
getdevnum warning: device "eprom" has size of zero
getdevnum warning: device "eprom" has size of zero
getdevnum warning: device "eprom" has size of zero
getdevnum warning: device "eprom" has size of zero
device does not contain a valid file system
dir: cannot open device "eprom:"
rommon 7 > dev
Devices in device table:
id name
flash0: compact flash 0
flash: compact flash 0
flash1: compact flash 1
bootflash: boot flash
usbflash0: usbflash0
usbflash1: usbflash1
eprom: eprom
rommon 8 > boot flash
program load complete, entry point: 0x80803000, size: 0x1b340
open(): Open Error = -66
boot: cannot open "flash0:"
an alternate boot helper program is not specified
(monitor variable "BOOTLDR" is not set)
and unable to determine first file in bootflash
loadprog: error - on file open
boot: cannot load "flash"
rommon 9 > boot bootflash:
Invalid devbase
device does not contain a valid FS
boot: cannot open "bootflash:"
boot: cannot determine first executable file name ondevice "bootflash:"
rommon 10 > dir boot flash dor ir flash0:
program load complete, entry point: 0x80803000, size: 0x1b340
open(): Open Error = -66
dir: cannot open device "flash0:"
rommon 11 > dir flash1:
dir: cannot open device "flash1:"
