Can re-use/re-purpose the licenses purchased on a current 6148s, on a new 6248 Switch?
Can re-use/re-purpose the licenses purchased on a current 6148s, on a new 6248 Switch?
Hello I have a customer running Cisco UCS with blade chassis and 6248 FIs in primary datacenter. now customer want to setup a DR host in a secondary site, where they want to place DR VMs (DC, SQL AlwaysOn replica, etc.). My question is, that if cu...
Hi UCS System : UCS Mini / Firmware 3.1(2b)i Now I see this Error code F1000020 the discription is as follows <faultInst ack="no" cause="fsm-failed" changeSet="" childAction="deleteNonPresent" code="F1000020" created="2011-02-25T04:16:22.037" descr=...
We have a UCS mini that is cabled directly to a Netapp 2552 array. We want to use Ethernet (FCoE) for the connections from the UCS chassis to the Netapp array. Port 1 is configured as an FCoE Storage Port (assigned to the VSAN on Fab A/B each) -- th...
Hi team,As discussed with TAC engineer about this SR 680643379.suggest to get the more details about the OID's details from the cisco Dev team.We are using C series UCS C220 - M3S we need to monitor the device through Nimsoft tool.We need some more i...
I had updated our UCSM from 2.2.3e to 3.1.1h successfully a couple of weeks ago and then felt comfortable enough with proceeding with the Server Firmware updates after updating our DR/Test environment successfully. The update failed and now I'm stuck...
loader> boot tftp://172.16.1.100/n7000-s2-kickstart.6.2.6a.bin Address: 172.16.1.2Netmask: 255.255.255.0Server: 172.16.1.100Gateway: 0.0.0.0 Filesystem type is tftp, using whole diskBooting: /n7000-s2-kickstart.6.2.6a.bin console=ttyS0,9600n8nn quie...
Hi Experts, I have couple of UCSC-C220-M4S that will be directly connected to Fabric Interconnect without going through a FEX. The Fabric Interconnect will be connected to Nexus 5K. I know how to set up FI cluster and configure uplink ports and serve...
Hi, Would someone know where can I download MIBS for Cisco Integrated Management Controller (Cisco IMC) [UCS C220 M4S] Firmware Version 2.0 (10b). Thank you.
Hi, Would someone know where can I download MIBS for Cisco Integrated Management Controller (Cisco IMC) [UCS C220 M4S] Firmware Version 2.0 (10b). Thank you.
Hi Our client have UCS-C210M2-VCD2. It contains 10 146Gb 15K disk RAID 5. 146Gb 15k disk from Cisco are in EoS... Two of them indicate about a problem. Can we replace it with server supported 300Gb 15K disks? can we use Dell 146Gb 15K disks?
Can I replace a b200 blade with am older CPU type with anew B200 with a Haswell chipset by just adding the new to the same slot as the old. We are using boot to SAN
Dear Friends, I will implement a new UCS project and I have this Part Number C1UCS-OPT-OUT for each Blade Server. I take a look in the Cisco site but I didn't find any reference to it. If someone could explain me what is this Part Number is for I w...
Hi, Need some advice with switching from FC Switching mode to FC End Host Mode. Is it possible with no downtime (other than restarting hosts to add/remove vHBA’s)? We currently have one storage directly attached to our FI’s. My task is to connect FI...
Hello,We have Rack server with two VIC 1225, managed by UCSM(single wire management), Single Wire Management of rack serveer only supports single NIC. Is there anyway to use second NIC as redundancy , in case one VIC 1225 fail?Thanks in advance ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-15-2024 11:16 AM | ||
08-15-2024 08:03 AM | ||
08-14-2024 07:32 AM | ||
08-02-2024 03:36 AM | ||
07-23-2024 08:42 AM |