B200M3 blade with Windows 2012R2 installed does not boot OS after firmware upgrade to 2.2(2c). UCSM shows no HW errors. Upgrade install passed smoothly.Try to power cycle, recover CMOS, but nothing changes. It boot in BIOS, no messages in console.
Before we have our network engineers reconfigure their infrastructure to allow network discovery from SCOM, does anyone know whether or not SCOM will include the virtual switches (Hyper-V or VMware), the UCS fabric interconnects, and the hosted virtu...
Hi all hope you can shed some light.I understood that the FI's switch east west traffic, Had an issue tonight where we removed Unplugged the north south portchannels to the layer3 network to upgrade the core and all VM's in the UCS lost connectivity ...
Enviroment: 2 x FI6296; 2 x 5108 with 6 B200M3 each. All servers have 2 x 300 GB SAS local drive, RAID 1.After upgrade to 2.2 one of servers indicates that local disks are missing (both of them). Invertory shows 0 disks in server. Two faults messages...
Is there any information about VM-FEX support for Windows Server 2012 R2 Hyper-V? In the middle of migration to 2012 R2 project and cannot go further without this.
I have had two recent cases of Flex Flash controller hanging up on two different C240 M3 servers. Luckily I have been able to resolve this issue by going into CIMC and resetting Flex Flash controller, but this is issue getting too frequent. We are us...
Hello,Does anyone know if the SCOM 2012 UCS pack can be used to monitor Cisco C-series server at the hardware level?If so, can it do this directly without going through UCSM (FICs)?If not, is there any sort of pack setup for monitoring of C-series se...
Hello,we have Central 1.1.(2a) running with a local database and we think about migrating that local postgres-db to an external db.Has anybody of you done that already?Or does anybody know, where to find a best-practive-guide?Thanks, Patrick
Having an issue getting UCS Central licensed for the 5 initial domains. Following documentation; I go out to license portal but there is no field for a GUID.I've clicked on just about every link with in the portal but have found nowhere to enter the...
Hello,I am running ESXI 5.1.0 build 1065491 and I keep receiving the error below the only way to get the server back is by rebooting it.Lost access to volume52fa9798-2f07f05f-c1f7-b0faeb97d646(datastore1) due to connectivity issues. Recoveryattempt i...
Hi Guys,Is it possible to upgrade the infrastructure firmware only to the latest 2.2 version and leave the blades on 2.0 or 1.3 firmware.Reason is its hard to get downtime to reboot blade and some new blades with V2 CPU requires new firmware. Jibby
Dear all,There are two UCS servers which the model is C240 M3 When I created RAID 5 for hard disks, CIMC shows Modrate fault. The warring message is storage virtual drive 0 degraded: please check the storage controller, or reseat the storage drive uc...
Any one come across this issue before. After we had upgraded our whole UCS environment to 2.2(1d) all the vnics fromour traffic monitoring sessions were gone and had to be added back in to the session.nothing in upgrade or release notes about it
Hello, I'm just doing a fresh new UCS install (2.2(1b)), and after having the error of the default keyring being invalid, I've regenerated it. What I'm now seeing in the event log of UCS is that at every 10 min, there is some post ...
Hi All, I have an issue, i created vlan 99 and added the ports and port-channel to the vlan on the ucs fabric interconnects and saved the configs. To my surprise nothing has changed, they are still on vlan 1 (default).See my configuration below.UCS-A...
