We have recently installed a few new B200 M3 servers, fully populated with 24 x 16 GB (1866 mhz) DIMMs, 2 x E5-2697 v2 CPUs.UCS manager shows the DIMMs properly in the inventory tab, but from the General tab, shows "Operating Memory Speed" of 1333 mh...
New deployment of a pair of 4500X in VSS mode and Cisco UCS.FI-A has 1 10G link to each 4500XFI-B has 1 10G link to each 4500XHow should the ports and port channels on the 4500X be configured for UCS uplinks?
I know how to set a remotely authenticated/authorized users Role using the Radius av-pairs with UCS. What Radius attribute/av-pair syntax is needed to set the users Locale within UCS? I have tried shell:roles="role@locales" and shell:locales="locale ...
I have a Cisco UCS blade chassis system that we have just finished setting up in the last few weeks. It is intended to run OpenStack and so we are trying to install some variation of Ubuntu on it. Except that when the blades boot, they seem to hav...
Hi All ...My Current Profile is Virtualization (VMware) and Much Intrested on UCSPlanning for the DCUCI Examination ...Please Help Me with the Below Information ...It will be Helpfull to Proceed on ....Pre-Requesites (Mandatory) :Cost of the Examinat...
Hi All,Did an upgrade from 2.1(3a) to 2.1(3b) , every component is upgraded to 2.1(3b) , except for the bios version.Am not able to view the package anywhere.. not in equipment>firmware mgmt> packages nor in the host firmware package > bios policyWou...
The OS installed fine, however, after several hours of sitting idle (overnight) it is frozen/hung. I have to do a hard reboot by holding the power button down for 10 seconds.I'm new to the Cisco UCS products. Just hoping someone has seen the same thi...
I was asked by many cutomers about ISSU support for the UCS Fabric Interconnect ? They all know, that N5K (without L3 module) supports ISSU. Is it on the roadmap ?
Should limit a vNic to use maximum of 5GB/s..
Hi .. am doing a remote installation of UCS with onsite support---- the blades are shipped with the sd cards but the team cannot see in from the front view.Where exactly will this sd card be located and how to verify the same in UCSM 2.1(3a).Thanks.
I recently upgraded our UCS domain from 2.1(3a) to 2.2(1b). We immediately ran into some critical errors which pointed to a few QoS Policies. The Rate(Kbps) setting cannot be set higher than 10000000. Be aware that it can cause quit some issues! Allo...
On the UCS server, that should be set alarm sound during the fault state. Actually, I had the three UCS servers coexited on the one rack. It is diffcult for us to identify which server making the alarm sound is. Can I change the alarm sound to become...
Hello folks,I am booting a couple of UCS servers (Redhat) from EMC VNX. Everything seems to be working fine, i can remove zones on one fabric, i can remove all zones to SPA or all zones to SPB ...PowerPath is doing its thing and the system keep runni...
I have two VSM's (vm's) running in HA pair on two blade servers in same HP chassis. In the beginning I was running the 1000v environment using the Eval licensing but now I have installed the Cisco provided license files.My question is this: When I in...
Hello, due to harddisk faulty, just replaced one local harddisk for UCS B200 M2 of of the blade. Locally check the harddisk light is green now, but from UCSM, the new harddisk information always showing unknown.Tested only after I run "recover server...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 05-09-2025 05:29 AM | ||
| 05-07-2025 03:02 AM | ||
| 05-07-2025 12:11 AM | ||
| 04-30-2025 01:15 AM | ||
| 04-21-2025 05:41 AM |
