ucs-c220-m3 with 1.4(6c) I am trying to add a UCS to a monitoring tool,.created a local account with read only accessconfigured the same credentials on the monitoring tool the protocol, port and Timeout interval are same getting an error saying th...
Forum Posts
Dear, I am relatively new to the subject of UCS, I am trying to make a cluster between the 2 Cisco UCS 6324 Fabric Interconnect, in the documentation that I have found they always mention connecting L1 with L1 and L2 with L2, but this Fabric Intercon...
Hello,I want to configure a port channel with 4 interfaces between an MDS 9148S and a UCS 6248UP.MDS 9148S version : 8.4(2)UCS 6248UP version : 2.2(8i) - 5.2(3)N2(2.28i)Here is the configuration: MDS: feature npivfeature fport-channel-trunk interface...
Hi, We recently did a firwmware update from 4.0(4h) to 4.1(2a) and for the FI A, we experienced a 10min outage. But for FI B there was no outage. The only differnece between the FI are the SFPs used. FI A is using H10GB CU3M but FI b is using SFP H25...
I was curious if it is possible to enable and use the physical 1GB ethernet ports on an HX240c that's a member of a UCS cluster? The only ports avail. in ESX are the 8 built into the twinax card, and when I browse the big hardware list it seems thos...
Hello,I have several blades in UCS that we intend to leave powered off. We do not intend to remove the blades from the chassis at this time because we may power them back on in the future if we need them to meet demand. We want them powered off in th...
Hello all,i'm in discussions with a customer on a "to-be-sold" HyperFlex Edge 3-Node-Cluster, which should have at least a bit of "stretched"-flavour, due to customer's limited budget. The customer asked, if it's possible to separate the servers and ...
Both disk1 and disk2 are degraded with this error message. Please suggest, is there any workaround or fix for this? Storage Local disk 2 is degraded: please take appropriate action by checking the detailed drive status Storage Local disk 1 is degr...
We are in need of purchasing a larger ssd drive for our UCS server. We want to make sure that we get the correct type of SSD for that system. Is there a specific type of SSD that we need to purchase for that system? ie. brand, sata type, etc. We are ...
The third psu out of the four psu does not power up in the chassis operating in psu grid mode. If I replace it, do I need to unplug the power cord 3 from the pdu in the back and replace it? Do we need to change the psu policy?Please let me know the p...
Can anyone point me in the direction of the part number for the sleds for this chassis? I cannot locate it online for the life of me. TIA.
The 2nd Gen Intel procs, namely, most of the 6000 series "R" SKUs have inlet temp requirements. The B200 M5 spec sheet says the 6248R proc is limited to 77F ambient temp if in slot 1-7. What happens when this is exceeded? It wouldn't be by much, but...
Hello, is it possible to connect a Cisco Meeting Server 1000 (PID: CTI-CMS-1000-M5-K9) to a FEX or Fabric Interconnect and administrate the server via UCS Manager? The Meeting Server has a VIC 1457 built in so I guess this is no problem. Does anyone ...
Hi, We need to move the Witness VM to another site and according to Cisco article we need Cisco TAC to facilliate the IP address changes. Could anyone confirm this? https://www.cisco.com/c/en/us/td/docs/hyperconverged_systems/HyperFlex_HX_DataPlatfor...
Resolved! Setup UCS lab
Hi Any one have experience of setting up UCS lab using UCSPE. Can I setup the UCS lab at home? Do I need other physical devices? Thank you
