want to upgrade N5548UP from 5.2(1)N1(9) to 5.2(1)N1(9a) but the issu pre-check shows several port-channel interfaces, where servers are connected, as Non-Edge Ports although they are configured as "spanning-tree port type edge trunk" ... View more

Have a simple ACL: IPV4 ACL ERSPAN-FILTER         10 permit ip any 224.0.0.18/32 DS-J3-N5K-1(config)# monitor session 1 type erspan-source DS-J3-N5K-1(config-erspan-src)# filter access-group ?   WORD  Access control list name DS-J3-N5K-1(config-erspan-src)# filter access-group ERSPAN-FILTER ERROR: invalid argument DS-J3-N5K-1(config-erspan-src)# filter access-group ERSPAN-FILTER ?   <CR>    But I'm not able to apply it to an ERSPAN session on Nexus5548 version 5.2(1)N1(9) what is wrong here ... View more

I'm running catalyst 4948 on version 15.0(2)SG10 where by default the management interface is running in the VRF "mgmtVrf". you can use this IF for e.g. tacacas and ntp if you make them aware of the VRF but NOT for syslog: DS-N8-C4948-2(config)#logging 10.3.10.5 ?   <cr> DS-N8-C4948-2(config)#logging source-interface fastEthernet 1 Interface FastEthernet1 is not in the global table How to get this done for syslog?  ... View more

we see increasing output drops on a veth interface on a nexus 1000v. DS-N1K-10# sh clock Tue Apr 8 06:05:03 UTC 2014 DS-N1K-10# sh int Veth19 | incl Drops     0 Input Packet Drops 415678974 Output Packet Drops ... DS-N1K-10# sh clock Tue Apr  8 06:06:07 UTC 2014 DS-N1K-10# sh int Veth19 | incl Drops     0 Input Packet Drops 415701498 Output Packet Drops to figure out what is dropped we used vempkt capture but we dont see packets. Here the session output:   DS-N1K-10# module vem 3  execute vemcmd show port   LTL   VSM Port  Admin Link  State  PC-LTL  SGID  Vem Port  Type    ...    59     Veth19     UP   UP    FWD       0     0  LI-UAPP03a ethernet1  ...              DS-N1K-10# module vem 3 execute vempkt stop Will suspend log after next 0 entries DS-N1K-10# module vem 3 execute vempkt clear Cleared log DS-N1K-10# module vem 3 execute vempkt capture drop ltl 59 Successfully set packet capture specification DS-N1K-10# module vem 3 execute vempkt stop Suspended log DS-N1K-10# module vem 3 execute vempkt display detail all Also the exported capture file is empty:   DS-N1K-10# module vem 3 execute vempkt pcap /tmp/vempkt_capture_drop.cap Export Complete! DS-N1K-10# Is there a way to find out what is dropped? ... View more

I'm planning to upgrade N5K from 5.1(3)N2(1b) to 5.2(1)N1(4). "sh install all impact kickstart bootflash:n5000-uk9-kickstart.5.2.1.N1.4.bin system bootflash:n5000-uk9.5.2.1.N1.4.bin" reports: ... Compatibility check is done: Module bootable         Impact Install-type Reason ------ -------- -------------- ------------ ------      1       yes non-disruptive         reset ... Is the upgrade really non-disruptive? ... View more

The following message from ACS 5.4.0.46 is confusing me: "Configure Remote Repository under Purge Configuration which is used to take a backup of data before purge." cause it is configured: and it also seems to work cause I got also messages that the purge is beginning and that it was successful. What is the problem here? ... View more