Restarting the phone seems to help temporarily, but I still have the issue on our 7841 phones. We have tried sip78xx.11-5-1-18 and just loaded sip78xx.11-5-1SR1-1 to test.  It almost seems like a memory leak or something.  The phones are fine after a restart, but a few weeks later they are unbearably slow.  ... View more

Where can I get the capwap image?  Is it possible to get it from my controller?  I'm not authorized to get it through the CCO site.  Thanks! ... View more

Alrighty then.  I'll give it a try and report back. Thank you. ... View more

Here are my outputs: (Cisco Controller) >show sysinfo Manufacturer's Name.............................. Cisco Systems Inc. Product Name..................................... Cisco Controller Product Version.................................. 8.0.121.0 Bootloader Version............................... 1.0.20 Field Recovery Image Version..................... 7.6.101.1 Firmware Version................................. FPGA 1.7, Env 1.8, USB console 2.2 Build Type....................................... DATA + WPS System Name...................................... CORP-SR-WLC01 System Location.................................. System Contact................................... System ObjectID.................................. 1.3.6.1.4.1.9.1.1069 Redundancy Mode.................................. Disabled IP Address....................................... 192.168.0.50 IPv6 Address..................................... :: Last Reset....................................... Software reset System Up Time................................... 1 days 5 hrs 50 mins 47 secs System Timezone Location......................... (GMT -6:00) Central Time (US and Canada) System Stats Realtime Interval................... 5 System Stats Normal Interval..................... 180 Configured Country............................... US  - United States Operating Environment............................ Commercial (0 to 40 C) Internal Temp Alarm Limits....................... 0 to 65 C Internal Temperature............................. +31 C External Temperature............................. +18 C Fan Status....................................... OK State of 802.11b Network......................... Enabled State of 802.11a Network......................... Enabled Number of WLANs.................................. 7 Number of Active Clients......................... 62 Burned-in MAC Address............................ 68:EF:BD:94:1B:20 Power Supply 1................................... Present, OK Power Supply 2................................... Absent Maximum number of APs supported.................. 500 System Nas-Id.................................... CORP-SR-WLC01 WLC MIC Certificate Types........................ SHA1 (Cisco Controller) >show time Time............................................. Fri Jan 29 15:50:58 2016 Timezone delta................................... 0:0 Timezone location................................ (GMT -6:00) Central Time (US and Canada) NTP Servers     NTP Polling Interval.........................     7200      Index     NTP Key Index                  NTP Server                  NTP Msg Auth Status     -------  ----------------------------------------------------------------------------------        1              0                               192.168.52.11       AUTH DISABLED        2              0                               192.168.52.12       AUTH DISABLED show ver Cisco IOS Software, C1140 Software (C1140-K9W7-M), Version 12.4(21a)JA1, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2009 by Cisco Systems, Inc. Compiled Wed 16-Sep-09 18:09 by prod_rel_team ROM: Bootstrap program is C1140 boot loader BOOTLDR: C1140 Boot Loader (C1140-BOOT-M) Version 12.4(23c)JA6, RELEASE SOFTWARE (fc1) ap uptime is 1 minute System returned to ROM by power-on System image file is "flash:/c1140-k9w7-mx.124-21a.JA1/c1140-k9w7-mx.124-21a.JA1" This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately. A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html If you require further assistance please contact us by sending email to export@cisco.com. cisco AIR-AP1142N-A-K9     (PowerPC405ex) processor (revision A0) with 98294K/32768K bytes of memory. Processor board ID FTX1650K28U PowerPC405ex CPU at 586Mhz, revision number 0x147E Last reset from power-on 1 Gigabit Ethernet interface 2 802.11 Radio(s) 32K bytes of flash-simulated non-volatile configuration memory. Base ethernet MAC Address: E0:2F:6D:C4:A1:B1 Part Number                          : 73-12836-06 PCA Assembly Number                  : 800-33767-06 PCA Revision Number                  : A0 PCB Serial Number                    : FOC16466SUX Top Assembly Part Number             : 800-33775-05 Top Assembly Serial Number           : FTX1650K28U Top Revision Number                  : A0 Product/Model Number                 : AIR-AP1142N-A-K9     Configuration register is 0xF ap# using  eeprom values WRDTR,CLKTR: 0x84000800 0x40000000 RQDC ,RFDC : 0x80000034 0x00000200 using HYNX ddr static values from serial eeprom ddr init done Running Normal Memtest... Passed. IOS Bootloader - Starting system. FLASH CHIP:  Numonyx P33 Checking for Over Erased blocks ................................................................. Xmodem file system is available. DDR values used from system serial eeprom. WRDTR,CLKTR: 0x84000800, 0x40000000 RQDC, RFDC : 0x80000034, 0x00000200 PCIE0: link is up. PCIE0: VC0 is active PCIE1: link is up. PCIE1: VC0 is active PCIEx: initialization done flashfs[0]: 144 files, 7 directories flashfs[0]: 0 orphaned files, 0 orphaned directories flashfs[0]: Total bytes: 32385024 flashfs[0]: Bytes used: 5544448 flashfs[0]: Bytes available: 26840576 flashfs[0]: flashfs fsck took 20 seconds. Reading cookie from system serial eeprom...Done Base Ethernet MAC address: e0:2f:6d:c4:a1:b1 Ethernet speed is 100 Mb - FULL duplex Loading "flash:/c1140-k9w7-mx.124-21a.JA1/c1140-k9w7-mx.124-21a.JA1"...########################### File "flash:/c1140-k9w7-mx.124-21a.JA1/c1140-k9w7-mx.124-21a.JA1" uncompressed and installed, entry point: 0x4000 executing... enet halted               Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013.            cisco Systems, Inc.            170 West Tasman Drive            San Jose, California 95134-1706 Cisco IOS Software, C1140 Software (C1140-K9W7-M), Version 12.4(21a)JA1, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2009 by Cisco Systems, Inc. Compiled Wed 16-Sep-09 18:09 by prod_rel_team Proceeding with system init Proceeding to unmask interrupts Initializing flashfs... flashfs[1]: 144 files, 7 directories flashfs[1]: 0 orphaned files, 0 orphaned directories flashfs[1]: Total bytes: 32385024 flashfs[1]: Bytes used: 5544448 flashfs[1]: Bytes available: 26840576 flashfs[1]: flashfs fsck took 5 seconds. flashfs[1]: Initialization complete....done Initializing flashfs. Radio0  present A600 8000 90020000 0 90030000 B Radio1  present A600 8000 98020000 0 98030000 0 Ethernet speed is 100 Mb - FULL duplex This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately. A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html If you require further assistance please contact us by sending email to export@cisco.com. cisco AIR-AP1142N-A-K9     (PowerPC405ex) processor (revision A0) with 98294K/32768K bytes of memory. Processor board ID FTX1650K28U PowerPC405ex CPU at 586Mhz, revision number 0x147E Last reset from power-on 1 Gigabit Ethernet interface 2 802.11 Radio(s) 32K bytes of flash-simulated non-volatile configuration memory. Base ethernet MAC Address: E0:2F:6D:C4:A1:B1 Part Number                          : 73-12836-06 PCA Assembly Number                  : 800-33767-06 PCA Revision Number                  : A0 PCB Serial Number                    : FOC16466SUX Top Assembly Part Number             : 800-33775-05 Top Assembly Serial Number           : FTX1650K28U Top Revision Number                  : A0 Product/Model Number                 : AIR-AP1142N-A-K9      Press RETURN to get started! *Mar  1 00:00:06.825: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed *Mar  1 00:00:06.835: *** CRASH_LOG = YES *Mar  1 00:00:08.059: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0 *Mar  1 00:00:08.563: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1Base Ethernet MAC address: E0:2F:6D:C4:A1:B1 *Mar  1 00:00:10.752: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up *Mar  1 00:00:11.752: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up *Mar  1 00:00:19.754: AUTOINSTALL: GigabitEthernet0 is assigned 192.168.0.115 *Mar  1 00:47:32.000: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down *Mar  1 00:47:32.000: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down *Mar  1 00:47:33.000: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down *Mar  1 00:47:33.000: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down *Mar  1 00:47:37.537: %SYS-5-RESTART: System restarted -- Cisco IOS Software, C1140 Software (C1140-K9W7-M), Version 12.4(21a)JA1, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2009 by Cisco Systems, Inc. Compiled Wed 16-Sep-09 18:09 by prod_rel_team *Mar  1 00:47:37.537: %SNMP-5-COLDSTART: SNMP agent on host ap is undergoing a cold start *Mar  1 00:47:38.511: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up *Mar  1 00:47:46.645: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 192.168.0.115, mask 255.255.255.0, hostname ap *Mar  1 00:48:32.833: %CDP_PD-4-POWER_OK: Full power - NON_CISCO-NO_CDP_RECEIVED inline power source ap> ... View more

Correct.  I thought that I saw a screen that showed all 25 licenses in use.  I had clicked on the wrong link.  The screen now shows 17 out of 25 in use.    I should have my morning coffee *before* I post questions to the forum.     ... View more

I was wrong.  They weren't taking up my licenses.  I got a new AP that needed a different DNS entry to point to the controller.  After updating that the new AP joined the controller as expected.     ... View more

This is absolutely ridiculous that Cisco hasn't fixed this issue yet.  I refuse to run older, vulnerable versions of Java.  And adding all of my ASA's certs is not an option.    C'mon, Cisco!  Get it together!     ... View more

Hi bsmith0013,   It sounds like you want to treat "0" as a directory number.  The easiest way to accomplish this (I think) is by creating a translation pattern.    In Unifiend Call Manager this can be found in the Call Routing tab and selecting Translation Pattern. Click the Find button to show any existing translation patterns.  I usually just copy an existing translation pattern and replace the values as needed.  Your DN "0" would go in the Translation Pattern box and then enter the DN of where you want the call to go in the Called Party Transform Mask text box.   Should be good to go.     ... View more