Update! We have completed this phase of the relabelling project early. This initiative aims to enhance your experience by making it easier to locate similar posts. To discover posts about the same device family, You can now click on the labels to sor...
-
3PCC
(1) -
3rd Party Call Control
(3) -
ATA
(5) -
ATA19X
(1) -
Buying Recommendation
(2) -
Call Control
(1) -
Cisco DNA
(1) -
Cisco IP Phone 6800 Series with Multiplatform Firmware
(8) -
Cisco IP Phone 7800 Series
(12) -
Cisco IP Phone 8800 Series
(15) -
Cisco Small Business SPA300 Series IP Phones
(11) -
Cisco Small Business SPA500 Series IP Phones
(71) -
Collaboration Endpoints
(1) -
Community Feedback Forum
(1) -
Headsets
(1) -
IP Phone and Accessories
(4) -
IP Phones and Accessories
(45) -
Other
(1) -
Other Collaboration Endpoints
(1) -
Other Collaboration Topics
(1) -
Other IP Telephony
(41) -
Other Unified Communications
(1) -
Peripherals
(1) -
Small Business Voice and Conferencing
(153) -
UC Applications
(4) -
UC Management-Licensing
(4) -
Unified Communications
(13) -
Voice Gateways
(13)
- « Previous « Previous
- Next » Next »
Forum Posts
Good morning everyone,I have a problem and I'm not sure how to solve it. I try to explain.I have a UC540 with severals SPA514G and everything works fine. Now we have added a sip trunk in the UC540 and it also works well but the problemis as follows, ...
Hello, I have a UC540 with severals SPA phones.I just enable a SIP trunk with 6 channels.My phone has four lines and each line support up to 2 calls, then my phone could receive up to 6 calls at maximun.In my incoming dial plan , I setup a blast gro...
Good Afternoon,Just looking for a bit of advice. I don't really have any experience in this area, but I've been asked to look into it anyway.We have a Cisco UC320 phone system. We are trying to use a dial-in voice-conferencing system that relies on i...
Hallo,I've uploaded, with TFTP, an updated italian dictionary (from cisco) for my SPA504G but the phone after reading and rebooting shows an empty blank screen, without life.I've tried:cisco firmware reset, but the phone doesnt bring up the network i...
Is there an option anywhere in the SPA series of phones to force a reboot every X number of days?
I'm not entirely sure which location/selection this should be in, please move if neciscary.I have been having some trouble for some time with using my phone connected to my modem via the SPA112. Whenever I call a place that has an automated message t...
HeyWe have a UC520 via analogue line.Now we want to switch to a SIP trunk and this works.Incoming and outgoing calls arrive, only when we call out does the number come through as an anonymous to the recipient.He seems to be calling out the number of ...
on a conference phone base model 8831, how many additional "Wireless" mics can be added if any?Note we already have 2 wired mics connected.
Hi!I am a Cisco SPA232D configured in bridge mode (...I already have a Cisco RV325 that does me the vLans routing work and it interfaces with my ISP's modem).The SPA232D is configured in vLan class 11 (...my native vLan is in class 1). I have a "big"...
Hi guys,I have a cisco SPA502G IP Phone, i have configured a new name under voice register global and also issued the 'create profile' command, but still if you call the extension it displays the old name.Kindly assist.Am using cme vesrion 8.6
Will SPA525G work with Spectrum IP Phone Network?
For the experts on this forum this might be a too easy question: I would like two connect two cisco spa 301 ip phones with one cisco sg300 switch between both. Just to be able to make phone calls from one ip phone to the other, nothing else. Which si...
I use Cisco SPA series phones and I utilize one touch button to park calls and the operator announces the parking lot number the call is parked on before the call is hung up.On the Cisco at least on Asterisk 11 this requires: Keep Referee When REFER ...
Hi,a customer has 4 SPA 303 - 7.5.5 all the same. In one there is this little noise/pitch like an interference, only in one of the four, the other three are4 OK. I included a mp3 file (in spanish) to hear the sound.Any idea, I would really appreciate...
I have about 10 Cisco 514G deskphones from my old provider and I've tried playing around with them however, I've noticed that they are locked down. I tried a factory reset but when I log in through the web interface I can see that under customisatio...