I have configured a UC520 with extra analog station ports so I can add a MD 4150 Motorola cordless phone. I may need two cordless phones down the road. Do you see any problems/challenges with adding this phone as an analog device into the UC520? I kn...
Dear All,Is it possible to change/upgrade my revision number in the Cisco Unity Express ? If "Yes" could you tell me how ? I want to upgrade it from 3.1 (current) to 3.2 in example.The current situation:UC500-CUE# show versionRevision:3.1 (pvr 8083 0...
I have problems with Linksys SPA2102 home gateway when I try to make connection with analog modem or SuperG3 fax connected to analog port of SPA2102 and using G.711 A-law codec. Does SPA2102 not support connections faster than 14.4kbps? I have atta...
Good day to all,recently I discovered a problem that I cannot resolve on my own.I have a UC520 with the latest software (not the newest 8.x).Everything is set up and running fine. I have a 7921G and a 7942G attached and registered to that UC520.The 7...
Dear Community,I'm trying to upgrade the firmware of a PAP2T v1 [1]. Both, the versions 3.1.22-LS and 3.1.23-LS (md5 hashes below [2]) failed repeatedly with the error message "Upgrade Failed: Version not matching". I also checked the Web-GUI as advi...
Hi,I was speaking with an SE and he said the real throughput of the WAN interfaces (100Mbps Ethernet) of the UC560 and UC540 is only about 20-25 Mbps.This could be a deal breaker for me as my client has a 100Mbps link. Is there a true datasheet on th...
We were not able to set up our UC 520 firewall with CCA to allow port forwarding to a couple of network storage servers and had to use CLI. Now I find that I need to open several ports to test VPN connection kits for a few client networks and even if...
ok ... this is a very weird problem. to me at least.i have two DHCP groups on an UC520. one for the clients (VLAN 1), one for the phones (VLAN 100).every SPA 525G gets an IP from the correct DHCP group, NO MATTER WHICH PORT. every 7975 gets an IP fro...
I've been trying to get the 7916 working properly with a 7965 phone. I've referenced here http://https://www.myciscocommunity.com/thread/7470 and followed the link given within. I've tried to remove the phoneload from flash and then reload it. Howeve...
Hello,We have a few 7960, 7975 and SPA525G phones, we would like to start doing video calls internally. Could we get some tips on the cameras to use such as recommendations for the cameras, etc, etc a
My call blast final destination is VM but I get a fast busy tone for an internal call and a busy tone when the call is from PSTN.I can reach the mail blast mailbox and leave a message when using the direct transfer to VM.Any ideas ?
Hi everyone,We are running a UC540 with 11x SPA504 phones. Of course QoS has been applied. Customers complain about the low level of volume of both incoming and outgoing calls. Is there a way to tune this audio level to better dB level?Thanks in adva...
Hi:Can anyone tell me why or how to fix an issue with the Cisco UC500. We are getting an unknown SIP Registration message from the Cisco UC500. I don't even have the '6782367070' programmed anywhere in UC500. So, I don't how it is sending out this SI...
Hi all,I'm having difficulty with 7931 phones and overlaid call-waiting ephone-dn'sThe phones use all the button's, and for inbound call's, these are overlaid with the call-waiting option on 1 button.However if a call is active on a phone on that but...
I'm trying to get CIPC to work on my CME.My two issues, (one minor, one more difficult)1. I need for it to be a member of our helpdesk hunt group. I'm able to get the hlog button to work and it can log in and out of the hunt group. The only issue ...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: