VPN

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Cisco CyberSecurity

Labels

Forum Posts

Is there a way to force clients that are already installed to download an updated client profile XML file from the ASA.  I have tried editing the existing client profile xml file on the ASA, but the already deployed clients do not seem to download th...

conleya by Level 1
  • 3119 Views
  • 1 replies
  • 0 Helpful votes

Resolved! IPsec over tcp

Hello ,I am looking for a sample config for IPsec over tcp (port 1000) for cisco 12.4 ios (2610xm)regards,Andrew

andre8525 by Level 1
  • 3220 Views
  • 11 replies
  • 0 Helpful votes

Hi all,  When It Is Suggested use the Perfect Forward Secrecy (PFS)?I would like to know if it's appropriate use of Perfect Forward Secrecy (PFS) in a scenario where the VPN based on Dynamic-to-Static IP address?Any best practice are welcome!Best reg...

parkerTod by Level 1
  • 4598 Views
  • 1 replies
  • 0 Helpful votes

I’m new to this so please excuse me if this seems like a silly / basic question.We recently installed a new SA520W. We have 5 static ip address assigned to my company, X.X.X.120 thru .124.We have set up X.X.X.121 as our WAN port and 192.168.1.X as ou...

HiI need to set up a site-to-site VPN on ASA 5505 (ASA version 8.4) on a private IP address range to a third party who have are using internet routable IP addresses for the remote LAN.E.g. in the Protected Networks settingsLocal Network: 192.168.1.0/...

Hello,I'm not expert in ASA and routing so I ask some support the following case.There is a Cisco VPN client (running on Windows 7) and an ASA5505.The goals are client could use remote gateway on ASA for Skype and able to access the devices in ASA in...

fbela by Level 1
  • 858 Views
  • 3 replies
  • 0 Helpful votes

Hello Community,I have a particular setup in mind, but can't get it to work in a GNS3 environment to have it tested before trying it in our production setup.We have a setup using two VPN routers (3845) with HSRP, BGP and VRF (with rri), using a class...

avinashpi by Level 1
  • 921 Views
  • 0 replies
  • 0 Helpful votes

We have ASA 5510, running IOS 8.2(4).  We are setting up two VPN pools for Cisco VPN client.  Do we need to setup each NAT statement for each VPN pool?  How do we setup the NAT statement for the second VPN pool?Below is my current config:ip local poo...

I'm running a Cisco 891 it has both crypto maps and ipsec VTI's running on the external interface. The cryto maps are for sites that do not have a cisco router and the Tunnels are for the sites that use crypto maps work perfectly fine. But I much pre...

folksi'm setting up a vpn with traffic initiated from clients behind a 2800 router to a web server behind a remote asai've a small lab in gns3 with a router to router setup first and then with router to asa which i'm using to test configsmy query is ...

Using RV042 router,have an office with 4 computers XP PRO SP3 and only 2 need to use the VPN connection.problem is each one will connect just fine BUT when one is connected the other will not connect untill the other is disconnected.have another offi...

How do you temporarily disable a point to point vpn connection?  I tried this command:no crypto map mymap 30 set peer x.x.x.xbut I got this error message "This crypto map is incomplete. To remedy the situation add a peer and a valid access-list to th...