VPN

Hi all,I have a site to site VPN, with site A being 172.16.1.x and site B being 172.16.2.x.Site B also has DMZs 192.168.1.x, 192.168.2.x, 192.168.3.x and 192.168.4.x.The site to site VPN works as expected, but I would like users in site A to be able ...

Hello all, I have a PIX506 with 6.3.4 and working vpn solution. Clients use the Cisco client to connect to the vpn on the PIX. I have a need to have a specific IP assigned to a particular remote client. Is there a way to set up DHCP lease reservat...

Hi--I've configured EZVPN, client connect with VPN client 4.01, We can access exchange using Outlook Web Access but we cannot using Microsoft Outlook.need assistance.Tks

I have 2 Cisco 2651 and I'm trying to configure a IPsec tunnel between them, but when I try to use the command crypto in the configure terminal doesn´t exists, Is not possible by default the configuration of IPsec in all the routers? Do I need a lice...

I am having a problem in one of my vpn link using pix to pix. I invoked the SH IPSEC SA and it shows that encryption was okay but theres zero packets on the decryption part.thanks

HiI have a router with below config and am unable to VPN from heind the router to a VPN concetrator on the internet. It worked previously with a cheap home ADSL router but not with the Cisco one. can you VPN from behind a cisco router acting as a fir...

Hi,I have a PIX 515E IOS 7.1.2 and I get too much logs like that :713903: IP = xxx.xxx.xxx.xxx, Error: Unable to remove PeerTblEntry713902: IP = xxx.xxx.xxx.xxx, Removing peer from peer table failed, no match!I don't know why I get that... if you hav...

If bri isdn interface is backup by serial interface. Two commands are president for timeout bri interfaceone under backup serial interface1. backup delay 10 30The other under bri interface2. dialer idle-timeout ...

Hello,I am experiencing a problem, I have a 3002 and a 3005 doing Lan to Lan tunnel betwenn the two, and the clients that are behind the 3002 cannot open a VPN tunnel to their companies ( example: Microsoft VPN connection)over the tunnel lan-to-lan I...

I am trying to configure both Easy VPN server and remote on Cisco 836 IOS 12.4(6)T1. It is possible to get Easy VPN server working or Easy VPN remote working but not both at the same time. According to the release information it should be possible to...

Hi Everyone, I am trying to configure SSL VPN Client with Certificates, the issue is that it needs to be configured for RADIUS. I am unable to find any decent documentation that describes step by step what needs to be done on both the VPN Concentra...

US serves<->US PIX<==>HK PIX<->HK serversWe have already established VPN Tunnels successfully. PING test is ok.If I add a server(DMZ server) which is outside HK PIX, Do US servers accesss DMZ servers?IF yes, how?Thank

IPSEC AH SECURITY & ESP PROTOCOLS USES TWO TRANSPORT AND TUNNEL MODES. IN ALL AH & ESP FOUR MODES IP PACKET IS EXPANDED USING 3DES AND AESHOWMANY BYTES THE IP PACKETS ARE EXPANDED USING ALL MODES PROTOCOL MODES (3DES) (AES) =...

Hi there.I'm running Ubuntu "Dapper Drake" 6.06 Beta 2 and I'm unable to install the 4.7 version of the client :-(I'm using GCC 3.4 as a compiler, not 4.0.Here is the output from the install:jjs@itchy:~/cisco_vpn/vpnclient$ ./vpn_installSorry, you...

ASA7.1(2). I configured split-tunnel network list for a group with deny action but it doesn't works. means the deny entry is not showing in the VPN client's routing detail. is this expected behavior or something wrong?Thanks in advance,