Buy or Renew
Buy or Renew

VPN

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

Cisco CyberSecurity
Labels

Forum Posts

Start a conversation

Resolved! ISR 4331 as GetVPN KS?

Hi all, Would 4331 router work as GETVPN key server for about 30 GMs? All the documents I have found key sers are using the old ISR.  Please let me know if 4331 would work or a different suggestion!   Thank you.

NL17 by • Level 1
  • 971 Views
  • 1 replies
  • 0 Helpful votes

Resolved! VPN Tunnel goes down

Hi All, We have configured Site to Site VPN between ASA and Palo Alto. Where ASA is the initiator. But the requirement is that we have traffic generation from Palo Alto end also. We have observed that tunnel goes down when there is no traffic from In...

shafhuss by • Level 1
  • 4508 Views
  • 2 replies
  • 0 Helpful votes

Split-dns configuration

I need the VPN users to access one specific server externally What I have done specify the internal domain to the splig-dns configuration. I have not configured any access-list, as I need the users to resolve the server domain name to the external IP...

erga by • Level 1
  • 1908 Views
  • 4 replies
  • 0 Helpful votes

NAT-T with Site to Site IPSEC

I have a question about setting the peer address when you use NAT-T in a site to site vpn.   Using an ASA (8.4) and PIX515E(6.3(5)) I have built a working site to site VPN.   Now i want to move the Pix behind a router doing PAT. I have turned on Nat-...

psandy by • Level 1
  • 480 Views
  • 2 replies
  • 0 Helpful votes

After disconnect, VPN is not useable again until reboot

I'm using any connect 4..5.04029 on Linux (ubuntu 17.10). I'm able to connect using 2-factor authentication to a remote server, exactly once. After disconnect (whether I issue the disconnect command, or a timeout is forced from the other side) I cann...

ermac by • Level 1
  • 510 Views
  • 0 replies
  • 0 Helpful votes

Resolved! ASA 5510 ipsec vpn help

I have been tasked with allowing users to vpn into a particular server that is running on interface 0/2 at the main site on an asa 5510.  Looking for a little help on this one.  This is what I am working with, we have a site to site vpn between 2 off...

j_lorang1 by • Level 1
  • 751 Views
  • 2 replies
  • 0 Helpful votes

Regarding Transfer speed in Cisco Any Connect

Hi,I was trying to check transfer speed from Cisco Any Connect, with only ports opened in firewall 443 & 80 with 1 destination , but to complete data transfer of 50MB file it takes around 40mins, but if all ports are unblocked in Firewall with 1 dest...

Resolved! AnyConnect NAT and packet filtering

Dear Cisco Community,   I have several things that I would like to clarify with you regarding AnyConnect SSL VPNs.First is packet filtering and the other is NAT.   The ASA we use is basically a pure VPN gateway. There is no other traffic than tunnels...

janiax by • Level 1
  • 1485 Views
  • 2 replies
  • 0 Helpful votes

Resolved! Main Mode Vs Aggressive Mode

Why and what scenario we choose Aggressive mode , any way its less secure and main mode is also not that slow , then what is use of Aggressive mode ?

Parth by • Level 1
  • 1475 Views
  • 2 replies
  • 0 Helpful votes

Cisco ASA Site to Site VPN traffic

Hi, Can some one assist,on how to confirm, whether the site to site vpn running on the ASA Firewall is up and passing VPN traffic. I have upgraded the Cisco ASA 5525 Firewall from ASA Code 9.1.3 to ASA Interim Code 9.6.4.3. We have multiple Customer ...

Load more