When using verizon 4G the android anyconnect constantly disconnects and reconnects. When it is connected for about 10 seconds it is working normally. This does not happen on the phone when the user is connected to wifi. It is only on 4G. 5|Oct 30 20...
Hello - We are trying to get the backup server list to work when a remote anyconnect user loses connectivity on the primary connection. Currently, it is getting stuck on trying to reconnect to the primary, rather than going to the next available one...
Hi,
We have 3-4 location which are given below.
1. HO = LAN Segment 172.26.4.0/22 & 172.26.150.0
2. Jabel Ali at Dubai LAN Segment 10.120.1.0/24
3. RAK at Dubai LAN Segment 10.110.1.0/24
4. US LAN Segment 10.120.8.0/23 & 192.168.0.0/24
HO end ...
Hello allI'm very new to VPN configurations.I am trying to configure a site to site VPN connection between a Cisco ASA 5505 and a Westermo DR-270 router.(http://www.westermo.co.uk/web/web_en_idc_com.nsf/AllDocuments/C9CFF9CF2339026BC1257BF300222A3F)T...
Hello Everyone, I have a problem setting up GRE tunnel ( w/o any encryption) between Cisco 2611 and 2621. IOS version is the same c2600-ik9o3s3-mz.123-26.bin.The problem is that after configuring both devices I can not ping 2611 from 2621 over tunnel...
Hi, Planning to deploy for customer a new firewall and we have chosen 5512-x.The need is to use webvpn portal and VNC plugin, like we have used with ASA5510. Now when i go to 5512-x downloads, there is only rdp plugin but not VNC plugin. Can i have c...
Hi, I have configured SSL web and anyconnect VPN on a cisco1941 router. When trying to connect to the VPN using a remote client, I get a DNS errormessage. Kindly assist. Attached is a screenshot of the error message
Hello everyone,I found the following statement in the Cisco ASA 5500 Series Configuration Guide using the CLI."Some clients may not support DHE, including AnyConnect 2.5 and 3.0, Cisco Secure Desktop, and Internet Explorer 9.0."I wonder, did this cha...
Hi all,I`m facing a strange issue with a customer. I`m using a Site-to-Site VPN between two ASA 5505 to connect his network to ours to replikate between a NAS on his side and a NAS on our side. I use the same setup with other customers and it`s worki...
hiI've been asked to see if we can virtualise our existing asa, it is used just to terminate our Anyconnect clients.From the reading, i can see i should be able to do 750 vpn sessions, if i have 4 vCPU license, and a Premium AnyConnect license for th...
When trying to use Anyconnect to connect a Mac computer to an ASA 5515 works fine from one Mac but try to connect with another Mac and get this error:"The VPN connection failed due to an unexpected internal error encountered by the VPN client."Ran DA...
Hi Everybody, I ' m getting stuck with on of my configuration ( Easy VPN Server)here is my configuration :crypto isakmp policy 5 encr 3des authentication pre-share group 2crypto isakmp client configuration address-pool local DHCP_VPN_Clientcrypto isa...
No config changes that I am aware of, it just suddenly stopped working.I am able to ping VPN user and VPN user is able to ping back... from voice vlan as well. VPN users are able to hear other VPN users using IP Communicator.When I call from LAN, VPN...
Hi Experts, I can now connect to my RA VPN however, when I checked my default gateway settings via cmd, I've got the second available ip in my ip pool. Is that normal? Is the RA VPN needs to have default gateway? Thanks, niks
