Wireless - Small Business

I have a Motorola WRG850G wireless router setup as a wireless bridge (router functions disabled).  The SSID, channel number & security options are set identical to the WRVS.  I assigned it a static IP address of 192.168.10.148.  My WRVS is 192.168.10...

Hi CommunityThe datasheet for AP541, describe that it is possibe to make a welcome screen for the Guest access."The solution even lets you provide a welcome screen to greet visitors using your guest network (it could be a welcome screen or company po...

I have this home user with a Di-641+ Dlink wireless router not acquiring dhcp ips. This is both with the Windows or Dell managing her wireless networks.  However, it works fine in our office connecting our Cisco AP541L access points.  Any ideas or su...

Hi,I just recently purchased a Linksys WAP4400N Access point and need guidance to set up with a Belkin Wireless router. Can anyone help me?Thanks

I need help with setting up a VLAN correctly.  I have a WRVS4400N V2 with the latest firmware.  Here is what I am trying to achieve:I want to setup 1 SSID for my office staff to access the Internet and our servers with and a second SIDD for visitors ...

For the next RVS4000 firmware, would it be possible to add a "mDNS Broadcast" checkbox to the Site-to-Site IPSec VPN Advanced setup?The advanced setup already supports NetBIOS broadcasts, which essentially lets the remote network see MS Windows-based...

Hi Team,I have got a couple of questions regarding AP541N antennas:1. Which type for the antenna connectors ? BNC or RP-TNC ? According to the doc:http://www.cisco.com/en/US/docs/wireless/access_point/csbap/AP541N/quick_start/guide/AP541N_QSG.pdf , i...

I have a question - regarding the new Cisco Small Business Pro 541 series AP, does anybody know the range/angle of the wireless "cloud" coming from the antenna?I have a 2 story office building that needs coverage. If I place the antenna downstairs ne...

Hi,I am looking to get coverage specs on a 1250 with an external omni-directional antenna, are there any specs sheets for distance in a clear line of site application for a tower mounted yagi or omni antenna connected to a 1250?Just to add to this, w...

5 v1 units here used across multiple different Dell PowerConnect gig switches in different buildings.  All have the same issues described here.  All are on the latest firmware 2.0.1.0 and it almost seems that made it worse than 2.0.0.12 was.  I'll be...

Hi,I´m working with a Cisco WAP4410N to get wireless access to my network. If I configure the AP to use WEP, everything is working fine. All hosts get an IP-adress via DHCP.When I change to WPA, I do not see any DHCP broadcast message on my network, ...

We have a Cisco 871w as our main firewall/router/wap, and two WRV4400S units that we use strictly as WAPs.  Call them FW, WAP1, and WAP2.  The radio coverage of the FW barely overlaps with WAP1 and WAP1 barely overlaps with WAP2.I would like to suppo...

HiI have a WRVS4400N and it basically disconnects everything connected to it on a daily basis and the only way of re-connecting to it, is by switching it off and back on again at the mains.It is sat behind an orange livebox which acts as the modem; s...

hello,I've had this WRVS4400N for a while now, but suddenly (not long after firmware update 2.0.0.8 K9) I've had this intermittent problem of it simply shutting down communication between any port every 24 hours, almost by the clock - I can still acc...

"For 2010, I resolve not to crash every few hours..."Hi all, I haven't posted in quite a while, but have been watching. The revelations of a new hardware version with the implied admission that V1 is defective, an underwhelming 'new' firmware that on...