08-17-2016 02:25 AM - edited 07-02-2021 03:48 PM
Hi,
I am experiencing a peculiar issue:
i have a 2504 running 8.0.120.0. I am trying to get a new 1850 running ap1g4-k9w8-tar.153-3.JD.tar. ver however whenever i try to get it to join to the controller i get a series of messages listed below.
i have tried upgrading and downgading the AP, tried doing a factory reset but none has worked for me so far.
This AP model is supported by controller version newer than 7.0.0.0!
Discovery response from MWAR ''running version 0.0.0.0 is rejected.
Failed to decode discovery response.
CAPWAP SM handler: Failed to process message type 2 state 2.
Failed to handle capwap control message from controller - status 4
Failed to process unencrypted capwap packet from 192.168.1.200
Failed to send capwap message 0 to the state machine. Packet already freed.
wtpProcessPacketFromSocket returned 4
Discovery Response from 192.168.1.200
wcp/RadDrv1 :: Dot11BaseDriver get_vap_if_index ioctl SIOCGIFINDEX failed for apr1v0 error No such device
[*07/29/2016 03:59:10.0181] wcpd: /local/build/JENKINS/workspace/Nightly-Cheetah-corsica-c8_3_throttle-FC3-CCO/base/../elts-meraki/elements/wcp/wcp_db.cc: 1184: void WcpDb::populate_if_index_table(): Assertion `if_index >= 0 && if_index < 64' failed.
[*07/29/2016 03:59:24.3136] ethernet_port wired0, ip 192.168.1.152, netmask 255.255.255.0, gw 192.168.1.1, mtu 1500, bcast 192.168.1.255, dns1 192.168.1.51, dns2 192.168.1.61, domain cgc.co
[*07/29/2016 03:59:37.4096] !!!!! {watchdogd} Process wcpd gone for 60s
this wcpd goes on increasing to 120/180/240 and so on till the AP resets.
Please help.
08-17-2016 02:29 AM
Hi,
1852 AP needs the minimum SW version of 8.1.111.0 on Cisco WLC to join.
Here is the compatibility matrix: http://www.cisco.com/c/en/us/td/docs/wireless/compatibility/matrix/compatibility-matrix.html
Please upgrade the SW on WLC and try again.
Regards
Dont forget to rate helpful posts
08-18-2016 12:24 AM
i have upgraded my Controller to 8.2.100.0... i am still facing the same issue.
08-18-2016 03:58 AM
paste the output of these commands:
from AP: sh version
From WLC: sh sysinfo
Also paste the boot-up process from cisco AP console.
Regards
Dont forget to rate helpful posts
03-25-2018 08:29 PM
03-27-2018 04:40 AM
Hi ,
Kindly post the below output from WLC.
debug mac <AP ethernet mac>
debug pm pki enable
debug capwap errors enable
From AP side :-
show version
Need AP console logs please
Additionally post below debug logs
debug capwap client error
debug capwap client event
You mentioned that you have upgraded the AP but didn't help . May I know which version were you upgraded to ?
Many thanks !
03-27-2018 05:05 AM
05-01-2018 09:31 PM
Hi All,
good day!
I also encounter the same issue. May we request to share your resolution for this issue.
05/01/2018 10:53:26.9135] waiting for WCP to initialize
[*05/01/2018 10:53:26.9135] waiting for WCP to initialize
[*05/01/2018 10:53:26.9135] waiting for WCP to initialize
[*05/01/2018 10:53:26.9135] waiting for WCP to initialize
[*05/01/2018 10:53:26.9135] waiting for WCP to initialize
[*05/01/2018 10:53:26.9135] waiting for WCP to initialize
[*05/01/2018 10:53:26.9135] waiting for WCP to initialize
[*05/01/2018 10:53:26.9135] waiting for WCP to initialize
[*05/01/2018 10:53:26.9135] waiting for WCP to initialize
[*05/01/2018 10:53:26.9135] waiting for WCP to initialize
[*05/01/2018 10:53:26.9135] waiting for WCP to initialize
[*05/01/2018 10:53:26.9135] Socket Invalid Element wcp/wcp_db Handler has_rlan Data 0 Length 10
[*05/01/2018 10:53:26.9135] CAPWAP State: Discovery
[*05/01/2018 10:53:26.9135] Discovery Request sent to 192.168.25.11, discovery type STATIC_CONFIG(1)
[*05/01/2018 10:53:26.9135] Discovery Request sent to 192.168.25.1, discovery type STATIC_CONFIG(1)
[*05/01/2018 10:53:26.9135] Discovery Request sent to 192.168.25.11, discovery type STATIC_CONFIG(1)
[*05/01/2018 10:53:26.9135] Discovery Request sent to 192.168.25.1, discovery type STATIC_CONFIG(1)
[*05/01/2018 10:53:26.9235] Discovery Request sent to 255.255.255.255, discovery type UNKNOWN(0)
[*05/01/2018 10:53:26.9235] CAPWAP State: Init
[*05/01/2018 10:53:26.9235] CAPWAP State: Discovery
[*05/01/2018 10:53:27.9231] Discovery Response from 192.168.25.11
[*05/01/2018 10:53:27.9231]
[*05/01/2018 10:53:27.9231] This AP model is supported by controller version newer than 7.0.0.0!
[*05/01/2018 10:53:27.9231]
[*05/01/2018 10:53:27.9231] Discovery response from MWAR ''running version 0.0.0.0 is rejected.
[*05/01/2018 10:53:27.9231] Failed to decode discovery response.
[*05/01/2018 10:53:27.9231] CAPWAP SM handler: Failed to process message type 2 state 2.
[*05/01/2018 10:53:27.9231] Failed to handle capwap control message from controller - status 4
[*05/01/2018 10:53:27.9231] Failed to process unencrypted capwap packet from 192.168.25.11
[*05/01/2018 10:53:27.9231] Failed to send capwap message 0 to the state machine. Packet already freed.
[*05/01/2018 10:53:27.9231] wtpProcessPacketFromSocket returned 4
[*05/01/2018 10:53:27.9231] Discovery Response from 192.168.25.11
[*05/01/2018 10:53:27.9231]
[*05/01/2018 10:53:27.9231] This AP model is supported by controller version newer than 7.0.0.0!
[*05/01/2018 10:53:27.9231]
[*05/01/2018 10:53:27.9231] Discovery response from MWAR ''running version 0.0.0.0 is rejected.
[*05/01/2018 10:53:27.9231] Failed to decode discovery response.
[*05/01/2018 10:53:27.9231] CAPWAP SM handler: Failed to process message type 2 state 2.
[*05/01/2018 10:53:27.9231] Failed to handle capwap control message from controller - status 4
[*05/01/2018 10:53:27.9231] Failed to process unencrypted capwap packet from 192.168.25.11
[*05/01/2018 10:53:27.9231] Failed to send capwap message 0 to the state machine. Packet already freed.
[*05/01/2018 10:53:27.9231] wtpProcessPacketFromSocket returned 4
[*05/01/2018 10:53:27.9231] Discovery Response from 192.168.25.11
[*05/01/2018 10:53:27.9231]
[*05/01/2018 10:53:27.9231] This AP model is supported by controller version newer than 7.0.0.0!
[*05/01/2018 10:53:27.9231]
[*05/01/2018 10:53:27.9231] Discovery response from MWAR ''running version 0.0.0.0 is rejected.
[*05/01/2018 10:53:27.9231] Failed to decode discovery response.
thank you.
Rey
05-01-2018 09:45 PM
05-01-2018 10:59 PM
Hi Moments,
Thank you very much for the answer. This helps a lot.
Regards,
Rey
05-01-2018 11:58 PM
Hi Moments,
good day!
is there any specific details from tac or documents that the issue is because of hardware failure?
thank you.
Rey
05-02-2018 01:07 AM
05-02-2018 01:10 AM
Thank you very much Moments. :)
05-16-2018 02:04 PM
@rgmamaril wrote:
[*05/01/2018 10:53:27.9231] This AP model is supported by controller version newer than 7.0.0.0!
What firmware is the controller running on?
11-09-2021 12:15 AM
Hi Rps-Cheers,
Hope you are doing well.
I have this problem now, as you said this should be a software bug, have you tried to upgrade the version of WLC? Or you just runs the RMA, and the problems didn't happen again?
Looking forward to your reply.
Many thanks
David
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide