Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Resolved! licensing requirements for WLC 5520
Hello, I have a question about licensing for WLC 5520, I need register 200 APs to WLC, Is it mandatory to buy licence for that, or it is included in AP price? Thanks for quick answer
Resolved! Cisco AP 2800 - Intel 8260NGW
Hi guys, I’m writing to you if you have advice for a weird problem I have here with a bunch of new Lenovo Yoga P40 (with wireless card Intel 8260NGW) working on wireless. This is the problem: When the computers join an access point Cisco 1040 and r...
I am trying to get the Cisco 1852AP to receive a DHCP address and as well as talk to the controller but unsuccessful: I currently have a DHCP Server, WLC and the Cisco 1852AP all connected to my 3750 switch. The DHCP server is in Vlan 210 and the WL...
Hello all, I am not sure if this is an issue or the way things actually work as this is the first time I have seen this issue. I have a user with a new Windows 10 PC. We have a Cisco 5508 controller and use Flexconnect for our APs at our remote locat...
We are getting the following errors from the Message History in AnyConnect Secure Mobility Client:[10/21/2015 7:45:19 AM] Service disabled.[10/21/2015 7:45:19 AM] Service unavailable.[10/21/2015 7:45:22 AM] Searching for a Network[10/21/2015 7:45:22 ...
With a controller-based 3802p, there are two internal 5 GHz radios. Want to know if it is possible or if others have implemented the following: 1) An internal 5 GHz radio be used for client access a) can an administrator assign a specific 5 GHz...
Recently we have been requesting RMA from Cisco for AIR-CAP3602I-A-K9 and AIR-CAP3702I-A-K9 using SORT. We are unable to log the RMA due to the following message: Please note that due to US Federal Communications Commission (FCC) regulations, the par...
Hi, We have 2 x Cisco Aironet 3702e Access Points in a bridge configuration, when I check the Current Rate (Mb/sec) I get items like below, what do these mean in terms on Mb/s? m4t2m6t2m6b2m3b2m10b2m1t2
Hi, I have a design requirement wherein I cannot connect the redundancy ports back to back on Cisco 8540 WLC. The requirement is to have the Primary and Secondary WLC in different datacenters. Thus need to connect them over the network over L2 where...
For a bigger project I had to setup a smaller PMIPv6 test lab (see attached picture). There are only two APs, 3 ISR 2911/K9 acting as MAG and LMA and some Ubuntu 16.04 LTS hosts. So far PMIPv6 without WLC works except Radius authentication from MA...
Hi Team , Have gone through the Cisco document and found that 5520 will supports up-to 1500 access points and i can see only added license of 50. Kindly provide me the below clarifications. Base license [AIR-CT5520-K9] will provide how many access...
Cisco社のマニュアル上で記載されている以下の状態に関して、後述の質問に対してご教授いただけますでしょうか。 *** マニュアル記載抜粋 *************************************************************** メッセージタイプ：動作状態 ステータスLED：青色、 緑色、 赤色の点灯が高速に切り替わる メッセージの意味：アクセスポイントの位置コマンドの呼び出し *** ここまで ******************************...
I have a new Cisco AP2802I-B-K9 access point that will not connect to my wireless controller. The controller is a WLC 5508 with software version 8.3.112.0. I have installed 3 identical access points that were ordered at the same time and those all co...
hi, i'm ignacio from chile, i have a WLC in Chile and one AP in Perú, that ap have a SSID with 802.1x autentication, that SSID work in flexconect. my problem is that we have very much reconections with Iphone devices and sometime the users cant conn...
Hello together, I have some issues with the WAP150: The Captive Portal on the WAP150 isn’t optimized for mobile devices. Most users for the guest-wlan are using mobile phones. So how can I activate mobile support? Is it possible to deactivate the po...
