Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hi Team,we have a setup for flex wlc with Guest WiFi services via C9800-CL Controller . we have meraki locally on each site which is acting as DHCP server. Scenario - i have two sites using same DHCP scope , tomorrow there is possibility that clients...
Hello, I'm trying to configure a wlc and an ap.I configured the wlc but when I try to connect it to the wlc it tells me :Client Excluded: MACAddress:f4:4e:05:80:60:4c Base Radio MAC :f4:4e:05:80:60:4c Slot: 0 User Name: unknown Ip Address: 192.168.10...
I'm not sure where else to post about this, so I'm starting here. For years, our Air Marshal has detected a rogue SSID called "DIRECT-". Since it appears on our LAN, we block it. I'm now looking deeper and would like to understand what this might be....
(disclaimer: homelab)Hey guys,I am having an issue with the interaction between the Juniper SRX320 and the Cisco WLC 3504. Wireless clients that have their gateway set and traffic handled on/by the SRX320, have their traffic either dropped or not fo...
EWC became EOS.I see that there are no replacementsCISCO got rid of the controller to sell it?
Hi !In my company ,some pc can't not connect to 802.1X WIFI 。The ISE log is shown that the username is "USERNAME", it is wrong，because i enter the username on the pc is "guest" . And also "12321 peap failed.....", just like the screenshot.And I c...
Hello Cisco 9800-Coders,I always get confused, when it comes to Wireless profile polices on this box.There is an annoying mismatch in naming of Your Policy profiles:The GUi states "Policy Profile" name, while the CLi states "profile policy" instead:W...
This issue started around the beginning of 2025. It is affecting multiple locations throughout the US with different Meraki AP models (MR42, MR44, CW91641, etc.).What appears to be taking place is gradually the AP will start losing its “up-stream” co...
Hi there!I support a couple of large shared space co-working locations (think of giant coffee shops on steroids). These locations can host over 200 people and the space is a combination of open floorplan, very large meeting rooms (host over 100 peopl...
Hello all, not sure if its relevent here, but i'll try my luck. So, we have recently setup SDA network and 802.1x in our network, and are currently in the process of testing 802.1x on wireless SSID. When a client joins our 802.1x wireless SSID there ...
Hi All - QQ - currently picking through a cluster of WLC's (4 in total) - 8540's.My understanding is that for inter WLC roaming to occur we need Mobility Groups configuring. Simply configuring the Default Mobility Domain Name across all four nodes d...
Hello,I was trying to do a Radioactive Trace and got this error:Error: Not enough disk space avaliable.The trace output was like this:executing cmd on chassis 2 ...sending cmd to chassis 1 ...executing cmd on chassis 1 ...Files being merged in the ba...
How is that I have disabled the alerts below in the new Alerts Configuration, but I still get these alerts (ethernet uplink speed degraded and low power mode) every day for various AP's across my networks (and after I have dismissed them too) ?Thanks
hi, I need to convert CISCO AIR-AP4800-E-K9 to Mobility express, Can you anyone help?
Can 9800 support the below ap model? any specific firmware version required?Cisco Catalyst 9120AXI-KCisco Catalyst 9105AXW-KAIR-AP1832I-Z-K9AIR-AP2802I-Z-K9AIR-AP3802I-B-K9AIR-CAP1532I-Z-K9AIR-AP1562IAIR-AP1542IThanks
